4 Front panel controls and displays .................................................................................................................. 4 Rear panel controls and connections............................................................................................................. 4 Remote control handset................................................................................................................................. 5 Remote control handset keys ..................

At the selected mounting site, the Sat jointed mast tripod with the mounted planar antenna BAS 60 or BAS 61 should not put you are others in danger. Ensure that the coaxial cable is laid in such a manner, that nobody can stumble over it and injury themselves. Mounting steps Open up the three-legged Sat jointed mast tripod. Attention! Make sure that you do not pinch your fingers when closing the tripod. Tighten the milled nut. Mount the planar antenna onto the jointed head. Loosen the cross

A) and apply the sealing glue evenly to the underside of the roof duct flange. Replace the roof duct in the drilled hole and press it firmly against the roof of the vehicle. • Apply the sealing glue evenly to the underside of the mounting plate, covering the whole area between the grooves (Fig. D). This area must be completely glued onto the roof of the vehicle, in order to achieve the necessary adhesive force. Place the mounting plate on the roof of the vehicle, as you have done already when ma

26210086 Input frequency range MHz 90-862 Input level range dB.V 48-78 Output frequency range MHz 5-65 Max. output level dB.V 113-118 Power consumption W 3.5 Transmission protocol DOCSIS/EuroDOCSIS 2.0 Suitable for VGO 939, VGO 939-1G, VGF 939, VGF 939-1G, VOS 952/953, VOS 952-1G, VOS 953-1G, ORA 9022, ORA 9022-1G, ORA 920/921, VGP 9033 as of version A03 (Nov. 2008), VGP 9033-1G, VGP 9041 as of version A02 (Nov. 2008), VGF 9030/9040 16 HTE 10 - Hand-held unit With the HTE 10 hand-held unit one i

To help you understand particular specialist terms that cannot be translated, we have added a short glossary at the end of the manual. The power switch is an environmentally friendly feature. If you will not be using your receiver for a longer period, you should therefore use the power switch to disconnect it from the power supply to save energy. For shorter breaks, you can switch the receiver to standby on the remote control, which uses only a minimal amount of energy. We wish you good receptio

Right after pressing the [OK] button, the made changes are saved! 4.1.2 Changing names of the favourite lists First, press the [OK] button. Select the entry field {NAME} with [0....9] or [Ў] [^] and activate it by pressing [OK]. The letters (capitalised a. small) or digits can be selected with the [Ў] or [^] button. You can move the entry position to the right and to the left with the [>] or [<] button. After entering the desired name, the entry field is deactivated by pressing [OK]. Textfeld: P

Then tighten the clamping screws again _____________________________________________________________ Fig. 5: Horizontal alignment Fig. 6: Vertical alignment AOI 65 AON 65 AOP 65 Order Number 212340 212344 212348 Channels 21-69 21-69 21-69 Gain dB 7-9.5 8.5-13.5 9.5-15 Reception range MHz 470-862 470-862 470-862 Full width at half maximum Horiz. Vert. ° ° 58-40 90-65 57-32 70-44 50-28 59-31 Front-to-back-ratio dB 20-25 21-26 22-28 Mast clamp range O mm 22-60 22-60 22-60 Length mm 410 814 1345 Win

935.434/C/ 935.434/C/0108/6.8d/e Mast installation and mast calculation (Fig. 1) .. Make sure masts is in vertical position when installing it .. Only use masts or standpipes specially designed for antenna installation. Other tubes mostly do not have the necessary stability to withstand heavy wind or other climatical situations. Kathrein masts and clamps fulfi ll these requirements. For an overview of the masts provided by Kathrein, see page 8 .. The clamping range of MULTIKA antennas‘ masting c

Selbststandiges Wiedereinschalten nach Abkuhlung / Mains supply is switched-off in case of overload. Automatic firing after unit has cooled down / L.unite est mise hors circuit en cas de surcharge. Mise en circuit automatique apres le refroidissement 2) Beispiele fur Stromentnahme-Moglichkeiten 2) Examples for current drain 2) Exemples pour courant consomme ¦ 14-V-Zweig¦ 14 V line¦ Ligne de 14 V - Max. 300 mA bei 18-V-Zweig: 0 mA - Max. 300 mA in 18 V line: 0 mA - Max. 300 mA a la ligne de 18 V:

To help you understand particular specialist terms that cannot be translated, we have added a short glossary at the end of the manual. The power switch is an environmentally friendly feature. If you will not be using your receiver for a longer period, you should therefore use the power switch to disconnect it from the power supply to save energy. For shorter breaks, you can switch the receiver to standby on the remote control, which uses only a minimal amount of energy. We wish you good receptio