net Display Size:.43’ high Front Panel Rating: NEMA-4X when mounted with gasket provided Case Material: Cycolac X-17 TOTALIZER Type: Up/Down Counting Digits: 8 digits positive/minus sign and 7 digits negative Scaler: 0.0001-100.0000 (0.0000 scales by 100 ) Decimal Point: 5 positions, programmable DC COMMON (Terminal 1) EXTERNAL RESET INPUT (Terminal 4) Resets totalizer when connected to dc common. Minimum Low Time: 0.25 to 1 .O sec. (maintained) The required pulse width varies with count speed,

Please check the functions of the instrument you have purchased before you proceed. RANGE Models Operating Range Overrange HHP-2000, 2020, 2080 25mbar / 10” HO2 350mbar / 140 H O2 ” HHP-2001, 2021, 2081 130mbar / 52 H O2 ” 1bar / 401 H O2 ” HHP-2002, 2022, 2082 2bar / 28 PSI 4bar / 58 PSI HHP-2003, 2023, 2083 7bar / 101.5 PSI 10bar / 145 PSI HHP-2024, 2084 External Transducer - HHP-2005, 2025, 2085 2bar absolute 4bar HHP-2026, 2086 10bar / 145 PSI 10.342bar / 150 PSI FEATURES Models Features HHP

Call toll free in the USA and Canada: 1-800-622-2378. FAX: 203-359-7811; International: 203-359-1660. FAX: 203-359-7807. BEFORE RETURNtNG ANY PRODUCT(S) TO OMEGA, YOU MUST OBTAIN AN AUTHORtZED RETURN (AR) NUMBER FROM OUR CUSTOMER SERVICE DEPARTMENT (IN ORDER TO AVOID PROCESStNG DELAYS). The assigned AR number should then be marked on me outside of the return package and on any correspondence. FOR w RETURNS. please have the fol-FOR BREPAIRS OR CALIBRATION. towing information available BEFORE cont

9 OUTPUT SIGNAL in Vdc ........................... 9 OUTPUT SIGNAL in mA ............................ 9 MATERIALS .............................................. 9 POWER SUPPLY ..................................... 9 MECHANICAL DIMENSIONS .................... 9 GALVANIC ISOLATION ............................. 9 GENERAL SPECIFICATIONS ................... 9 8-CAUTIONS, WARNINGS AND NOTES............... 10 SAFETY CONSIDERATIONS PRESCRIPTION.Before starting any operation for replacement, maintenance

Replacement Pan: DPClO-BAT Speed: 0 to 10 kHz Minimum Low Time: 80 microseconds PHYSICAL Minimum High Time: 20 microseconds Operation Temperature: 0”-55°C (The above times are with a 0 to 5.0 V swing.) Storage Temperature: -20-70°C Input Impedance:2kS2 above 5 V dc Operating Humidity: 90% Non-condensing Voltage Thresholds: Low 0 to 1.2 V dc Weight: 2.2 oz. net High 2.0 to 28 V dc Display Size: .43” high Max. High 28 V dcFront Panel Rating: NEMA-4Xwhen mounted with gasket provided. RESET INPUT (T

To continue pumping, turn on the unit’s power. The display returns to the STOPPED Display Mode and shows the current RPM setting. The accumulated time of pumping and volume dispensed is reset to zero. Then press the START/STOP key. START STOP xxx rpm Pump(s) stops; press again pump(s) starts To resume pumping at the current setting, press the START/STOP key. The display enters the RUNNING Display Mode, and the fluid begins to dispense. INLET SELECT Must STOP first! LEDs indicate new pump directi

Use a medium to hard roller to Do not wrap the heater over heater. © Copyright 2006 ENGINEERING, All rights reserved. This document may reproduced, translated, prior written ENGINEERING, MOUNTING YOUR HEATING BLANKET Installation of heater using factory supplied Pressure Sensitive Adhesive (PSA): 3. Peel off the release film [Figure A] and then press the heater onto the surface of the item being heated using a medium to hard rubber roller [Figure B]. Ensure blanket is making intimate contact wit

6.2.1 Pumping in the FLOW RATE Mode To pump fluid in the FLOW RATE Mode, do the following: 1. Set up the pump motor for pumping, according to Chapter 3. 2. Toggle the ON/OFF switch to turn on the unit’s power. The display is in the STOPPED Display Mode. Refer to Figure 6-3. 3. Either set the TUBE ID for the tube you are using (following Section 5.3) or calibrate the tube (following Section 5.5), before continuing. 4. Press the FLOW RATE key. FLOW RATE Display shows xxx mL/min ACTION Displays cur

OMEGA is constantly pursuing certification of its products to the European New Approach Directives. OMEGA will add the CE mark to every appropriate device upon certification. The information contained in this document is believed to be correct, but OMEGA Engineering, Inc. accepts no liability for any errors it contains, and reserves the right to alter specifications without notice. WARNING: These products are not designed for use in, and should not be used for, patient-connected applications. PX

Continuous Level Sensors should be installed rigidly so the float is free to move as the liquid level changes. 2. Continuous Level Sensors should be mounted in a tank area free of severe turbulence or protected from such turbulence by appropriate and adequate slosh shields. 3. Continuous Level Sensors stems should be vertical for best results, but satisfactory operation is possible in most liquids with the stem at up to a 30° angle from vertical. 4. Care should be taken that Continuous Level Sen