NL Bij reiniging de steker uit de wandcontactdoos halen. De papiervernietiger niet zelf repareren. (zie pagina 24). I Rimuovere la presa di corrente prima di pulire la macchina. Non intervenire in caso di anomalie. (Vedi pagina 24). E Quite la clavija antes de limpiar la maquina. No lleve a cabo ninguna reparacion sobre la maquina destructora. (vease pag. 24). S Dra ut kontakten innan maskinen rengores. Utfor inga reparationer pa dokumentforstoraren. (Se sid 24). D Maschine darf ohne Sicherheits

Punching the Paper For the C340, always make sure that the punch handle is in the upright position before centering the paper. Load the first paper stack into the punch slot. Center the paper using the dial located at the front of the machine. Lower the raised handle until the paper is punched, and support the machine when lifting the handle to the upright position (Fig.4-A). For electric punching with the C450E: Load the first paper stack into the punch slot. Center the paper using the dial loc

Problem Solution No power Not plugged in Rollers stop during binding Operator is pressing too hard -- light pressure on the first four inches of the roller is all that is required Upper roller turns, but lower roller doesn’t Thread drive belt over pulley. The belt can be knocked off if a coil element threads too far Power cord has been lost Contact an authorized GBC technician, order replacement part #: 115v North America - 6200001 230v Europe - 6200002 230v United Kingdom - 6200014 240v Austral

Excluded from warranty are the dies which are subject to wear. GBC will repair or replace at our option the unit free of charge and return it prepaid. Please include a copy of your paid invoice. Any unit sent without proof of purchase will not be serviced free of charge. Instead such units will be serviced at the prevailing rates and returned C.O.D. This warranty does not extend to any GBC machine that has been subject to misuse, neglect, accident, or if the serial number has been altered or d

The GBC Shredmaster 2230S/2250X shredders are designed for small offices and low volume requirements. Innovative engineering has provided these shredders with the following operating and safety features: 1. Automatic Operation - The unit begins to operate when paper actuates the trigger in the shredder throat area. The motor stops running when the paper has cleared the cutting head and after the shredder has timed out. 2. Overload Warning - Whenever the capacity of the shredder is exceeded th

.. GBC4180 INTRODUCTION These instructions describe the use and function of two (2) laminators which, despite their varying widths, are similar in appearance and performance: MODELS FILM WIDTH GBC4120 12" (30 cm) GBC4180 18" (46 cm) GBC Laminators apply coated, transparent film to one but usually both sides of documents, photographs, or any sheet-like material. GBC laminating film consists of a polyester film coated one side with polyethylene-heat reactivatible adhesive. The film is applie

F Ne pas utiliser la machine sans son volet de securite (A). NL De machine mag zonder veiligheidsklep niet gebruikt worden (A). I Non utilizzare la macchina senza la pateletta di sicurezza (A) (Safety Flap)! E .No usar la maquina sin la tapa de seguridad (A)! S Anvand inte maskinen utan sakerhetsluckan (A). - 7 • Sicherheitshinweise • Safety precautions • • Consignes de securite • Veiligheidsvoorschriften • • Misure di Sicurezza • Normas de Seguridad • • Sakerhetsforeskrifter • 3870M • 3890D • 4

English 4 Francais 6 Espanol 8 2 a a g g e e d d f f b b c c Models: GLS28, GLX20 Models: GLM11, GLHS9 4 3 2 1 Illuminated Panel 3 Lights and Icons Explained 1 2 3 4 Power Reverse Door Bin on open full Color of LED Green Red Red Red Power on button pushed / no fault flash flash (6 seconds) flash (6 seconds) flash (6 seconds) Door open light light Bin full light light Auto button pushed / shredding light Forward jammed flash light Reverse jammed flash light Reverse button pushed light light Auto

GBC 1264WF/1244WF Operation Manual © 2006 General Binding Corporation Page 18 Display Control Panel-Continued Top and Bottom Temperature Use the up or down arrow keys to increase or decrease the set temperature of the heat rollers. The temperature shown on the display is the temperature at which the unit is attempting to attain. For example if the unit is set to 200*F even though the actual roller temperature may be higher or lower. To view the actual temperature press MEASURE. Stop The STOP but

We have taken numerous steps to assure that your shredder arrives in top condition. In the rare event that you do have any problems or questions, contact your dealer. IMPORTANT SAFETY INSTRUCTIONS Your safety as well as the safety of others is important to GBC. In this instruction manual and on the product are important safety messages. Read these messages carefully. A The safety alert symbol precedes each safety message in this instruction manual and on the product. This symbol indicates a p