. . . . . . . . . .3 Installation Instructions Drain connections . . . . . . . . . .7, 8 Important recommedations . . . .4 Installation instructions . . . . . .4-6 Planning and location . . . . . . . . .5 Programming the control . . . . . .9 Sanitizing . . . . . . . . . . . . . . . . . .10 Specifications and dimensions . . . . . . . . . . . . . . . . .11 Step-by-step instructions . . .7–11 Tools and materials required . .5 Unpacking and inspection . . . . .4 Operating Instructions, Tips Breaking

Sit back! Enjoy the comfort! Now pick a dominant leg. For most people this is your right leg, but go with whatever is most comfortable for you. Pick your leg up and swing the crank arm around so you can easily reach the pedal. If you are using toe straps, flip the pedal clip over your foot, but keep the strap nice and loose to start with. Swing the crank around until your foot is in a “cocked” position; somewhere close to the top of the pedal stroke. This spot is different for everyone, the key

If soft water is not directed to a faucet or fixture where wanted, consult a plumber. No salt in the brine tank or salt bridged • Check for a salt bridge or, if the tank is empty, refill with recommended salt. Press (for 3 seconds) the TOUCH or HOLD button to start an immediate regeneration and restore soft water supply. Transformer unplugged at wall outlet or power cable to softener not connected. Fuse blown or circuit breaker popped on circuit to electrical outlet. Electrical outlet on a circu

Manual No. 203709GS Revision - (04/20/2007) Thank you for purchasing this quality-built Briggs & Stratton pressure washer. We are pleased that you’ve placed your confidence in the DIAMOND brand. When operated and maintained according to the instructions in this manual, your Briggs & Stratton pressure washer will provide many years of dependable service. This manual contains safety information to make you aware of the hazards and risks associated with pressure washers and how to avoid them. Becau

If it becomes plugged with sand, dirt, etc., the water softening system will not work and you will get hard water. To get to the nozzle and venturi, remove the water softening system top cover. Be sure the water softening system is in service cycle (no water pressure at nozzle and venturi). Then, while holding the nozzle and venturi housing with one hand, remove the cap. Lift out the screen support and screen, then the nozzle and venturi. Wash and rinse the parts in warm water until clean. If ne

Warranty Advanced Transportation Products Inc. warrants each new VISION bicycle frame, fork, and seat frame against defects in workmanship and materials for the lifetime of the original owner. Paint and decals, seat fabric, and all original parts, are warranted for a period of one year from the date of purchase. This warranty is expresssly limited to the repair or replacement of a defective frame, fork, seat or defective parts and is the sole remedy of the warranty. This warranty applies to the

male pipe. If 1. pipes are needed, do not use the copper tubes and nuts included. Buy 1. pipe thread female adapter, and plumb directly to 1. threads. Clip END SIDE VIEW VIEW Bypass valve Valve body inlet or (push all the way in) outlet Fig. 3C Fig. 4 IN OUT Turn bypass valve upside down to connect to floor level plumbing Drain fitting on valve Valve drain hose FLOOR DRAIN Tie or wire hose in place 11.2. air gap STANDPIPE LAUNDRY TUB SUMP 7 Clamp Step-by-step installation instructions. 4A. CONNE

• Be sure the power switch is in the OFF position before plugging in the band saw. • Always disconnect band saw from electrical outlet before setting up or servicing. • Wear proper apparel. Never wear loose fitting clothes, neckties, jewelry and gloves that may get caught in moving parts. • Remove all wrenches before using band saw. Leaving wrenches attached while operating this tool may result in damage to the machine and/or operator. • Always wear safety goggles. Everyday eyeglasses have only