Halten Sieinenasen Lapen (6 bis 8 Sekunden) und unteren Sensor (siehe Abildung 3), bis die Pumpeingeschaltet von den Sensoren. Die Pumpe solte fur ANLEITUNG FUR INST ANDHAL TUNG UND W ARTUNG UbeSrcphraulftenrg Seihea ruesge lamnag.eisga dmemn erbindungen, um sicherzustelen, dasesin seiem Ew LIaNspGspeErndS.icChHt uRnAd A TTWOOD FUR TER Dieser Bilgenschalter Atwod besitzt oder www .atwoodmarine.T ensaio cno du’reannttr eceontinu Piece n . Appel rmpoaisux rie mlnau apmmo mpepres 12 4801 15A 80mA 1
These poles function as a guide device for the boat when taking it on and off the trailer. The Boat Trailer Guide Protectors simply slide on and fit tightly on the existing guide poles. The Boat Trailer Guide Protectors are designed to float up with the water height to help guide you on boat ramps with steep angles. Available in 4 sizes and a wide variety of colors! PART NUMBERS AND SPECIFICATIONS I.D. Length Color Aftermarket Packaging* 2" I.D. 36" Black 105693BK 2.5" I.D. 36" Black 105694
Die Pumpe T abele) betrieben werden. Der Schalter kan getrent von der Pumpe angebracht werden. Er kan auch an der Halterung jeder Pumpe der Serie T sunami (4606, 4608 und 4612) von Atwood angebracht werden. ! W ARNUNG: Dieses Produkt darf nur in Gleichstromsystemen eingesetzt werden. Bei der V erwendung in • Systemen, wo W echselstrom in Gleichstrom umgewandelt wird, kan es zu FunDkteiorn storungen kommen. Anschlus des braunen Drahtes an Mase kan den Schalter beschadigen. • Bei der Instalation u
Depress motor cartridge tabs, then twist cartridge counter-clockwise to remove. Figure 1 Lock Motor Cartridge Tab To Insert new motor cartridge 1. Check motor cartridge fit. Motor color must match housing color: 600 Series = RED, 800 = BLUE, 1200 = GRAY. 2. Coat O-ring with vegetable oil to ease insertion. 3. Insert cartridge into housing. Twist clockwise until you hear tabs snap up into slot. Figure 2 A WARNING To avoid leaking or sinking, the aerator RED TAB MUST BE LOCKED AND VISIB
Any expenses involved in the removal, reinstallation or transportation of the product are not covered by this warranty. The product must be returned to Attwood’s plant at the address above, postage prepaid, and insured with proof of original purchase including date. If Attwood is unable to replace the product and repair is not commercially practical or cannot be timely made, or if the original consumer purchaser is willing to accept a refund in lieu of repair or replacement, Attwood may refund t
REQUIRED FOR INSTALLATION • Adjustable wrench. • 1/4" - 20 diameter stainless fasteners. Fastener types can be bolts, or thread cutting bolts. Length must be no longer than1"(25mm) longplusthe thickness of the attachment base. • Four flat and four lock washers. If installing optional 7029-1 Locking Latch: • Cordless drill and 5mm diameter drill bit. • Two (2) #68 x 3/16" tri-fold aluminum rivets with .040"-.5" grip range. WARNING Read installation instructions carefully before installing seats.
Lights must be parallel to centerline of the boat (See Figure 1b). Figure 1a Figure 1b Green (Starboard) Red (Port) Red (Port) Green (Starboard) 3. Make sure there are no obstructions at the front or side such as rail stanchions, chocks, anchors, cleats, etc. within the light’s arc of visibility (112.5 degrees each side). bicolor light, location must be on the boat centerline. If installing a sidelight pair, both must be the same distance from the bow. At the marked location(s), make a mark for
not extend to any batteries or fuses used with the pump. This limited warranty is not applicable if the pump has been damaged by accident, improper installation, unreasonable use, lack of proper maintenance, unauthorized repairs or modifications, or other causes not arising out of defects in materials and workmanship. 3. Wire strippers. 4. Four (4) wire connectors or equivalent. POTABLE WATER PUMP 5. One (1) in-line fuse holder with 2 amp fuse. Attwood’s obligations under this warranty are limit
To prevent personal injury, disconnect the power source when installing or servicing this product. Always remove the boat from the water before using 120V AC power tools. DO NOT use pump to remove gasoline, oil or other flammable liquids. Always use the fuse amperage rating specified for your pump model. Failure to do so could result in serious personal injury or fire hazards. Attwood bilge pumps are designed to exhaust STANDING WATER ONLY. They are not intended to prevent rapid accumulation of
Rubber isolators are provided with each canister to allow for convenient installation. Vent Line Secure 5/8" vent hose with a clamp over each port (not included). Secure the vent hose as needed with hose mounting clamps for proper routing of hose and to ensure there is not stress on the hose at the connection to the canister. Integrated System Requirements Liquid fuel is not permitted to enter the canister. This can be managed by installing an in-line surge protector vertically +/- 45° as cl