E. Reassemble in reverse order and check system operation. MAIN FAN MOTOR – REPLACEMENT A. Shut off power at main breaker. B. Shut off gas supply and remove gas line and manifold lines from back of oven. C. Remove screws from motor cover housing and lift off. NOTE: When ovens are stacked, all motor cover housings are fastened together. D. Unplug power connector. E. Unplug thermocouple. F. Unplug 2 motor connectors. G. Remove 8 bolts from oven back ( 4 left, 4 right ) and lift out. H. Remove 1 sc

Require all operators to read this manual thoroughly before installing, operating or NOTE: servicing this equipment. Improper installation, adjustment, alteration, service or maintenance can cause property damage, injury or death. To avoid electrical shock that can cause injury or death, always unplug the unit prior DANGER! to proceeding with any and all maintenance or cleaning procedures! Do not work around conveyor belt with long hair, loose clothing, or dangling jewelry. DANGER! Getting caugh

GAS 120VAC 60 HZ. 1 PHASE MODEL 1116-080-A1 NAT. GAS 120VAC 60 HZ. 1 PHASE MODEL 1117-080-A LP GAS 120VAC 60 HZ. 1 PHASE MODEL 1117-080-A1 LP GAS 120VAC 60 HZ. 1 PHASE POWER SUPPLY Electrical power is supplied to the oven by a three-conductor cordset. Voltage from the black conductor to the white conductor is 120VAC. Black conductor is hot White conductor is neutral. Green conductor is ground. CONTROL BOX AUTO When the temperature in the control box reaches 120°F ± 3° (48.9°C ± 1.7°), theCOOL DO

3 SCHEMATIC............................................................................................................................ 5 TROUBLESHOOTING GUIDE ................................................................................................ 6 REMOVAL, INSTALLATION & ADJUSTMENTS................................................................. 12 GENERAL PARTS.................................................................................................................20 ADVANTAG

Fax: (260) 436-0735 Technical Service Hot Line (800) 678-9511 1100exportsvc REV: 12/8/05 TABLE OF CONTENTS SEQUENCE OFOPERATIONS 1104 THRU 1106...................................................... 3-4 SEQUENCE OF OPERATIONS 1134, 1135, 1136, 1150........................................... 5-6 SEQUENCE OF OPERATIONS 1151....................................................................... 7-8 SEQUENCE OF OPERATIONS 1152 THRU 1158.................................................... 9-11 SCHEMAT

NAT. GAS MODEL 1451 120VAC 60 HZ. LP GAS POWER SUPPLY Electrical power is supplied to the oven by a three conductor cordset. Voltage from the black conductor to the white conductor is 120VAC. The white conductor is neutral. The green conductor is ground. CONTROL BOX AUTO When the temperature in the control box reaches 120°F ± 3° (48.9°C ± 1.7°C), COOL DOWN the cooling fan thermostat will switch power to the control box cooling fan. The thermostat will interrupt power to the cooling fan when the

. . and thoughtful operation on your part. DO NOT INSTALL, OPERATE OR REPAIR THIS EQUIPMENT WITHOUT READING THIS MANUAL AND THE SAFETY PRECAUTIONS CONTAINED THROUGHOUT. Most importantly, think before you act and be careful. OPERATOR’S MANUAL Copyright© 2004 Lincoln Global Inc. • World’s Leader in Welding and Cutting Products • • Sales and Service through Subsidiaries and Distributors Worldwide • Cleveland, Ohio 44117-1199 USA Tel: 216.481.8100 Fax: 216.486.1751 Web Site: i SAFETY i WARNING CALIF

Remove mounting nut for fuse holder and remove fuse holder. 5. Reassemble in reverse order and check system operation. BEARING, CONVEYOR – REPLACEMENT 1. Remove conveyor from oven and place on flat work surface. 2. Remove connecting links from conveyor belt. See Installation and operations manual. 3. Remove conveyor belt from conveyor. Remove drive sprocket from drive shaft if required. 4. Move shaft toward end of conveyor, and shaft with bearings will now slip out of holding bracket. 5. Replace

DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILE IT IS IN OPERATION. WARNING: IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION, SERVICE OR MAINTENANCE CAN CAUSE PROPERTY DAMAGE, INJURY OR DEATH. READ THE INSTALLATION, OPERATING, AND MAINTENANCE INSTRUCTIONS THOROUGHLY BEFORE INSTALLING OR SERVICING THIS EQUIPMENT. · Obtain from your local gas provider and post in a prominent location instructions to be followed in the event gas odors are detected. · It is required that the oven be plac

Handles flux-cored welds on mild steel with ease. Practically everything you need to MIG weld mild steel is right in the box. Unit includes: • 4-Step Tap voltage control • Magnum® 100L welding gun and 10ft. (3m) cable assembly, with gas nozzle, .023” - .035” (0.6–0.9mm) cable liner and .023/.025” (0.6mm) contact tip • 10ft. work cable & work clamp • 6 ft input power cord with NEMA Type 5-15P plug • Guide tubes and reversible drive roll for .023-.035" solid MIG wire and .035" Innershield® flux-co