Simple push-button action delivers a shot of water which is immediately converted into steam. Because the amount of steam is consistent, it removes the guesswork and produces a uniform finished product from one operator to the next. This manual provides the safety, installation and operating procedures for the Deluxe Food Warmer (steamer). We recommend that all information contained in this manual be read prior to installing and operating the unit. Your Deluxe Food Warmer (steamer) is manufactur

D 08/05 Owner’s Manual EGG STATION (ES-600 & ES-1200) TABLE OF CONTENTS Owner Information .....................................................2 General ......................................................................2 Warranty Information .................................................2 Service/Technical Assistance ....................................3 Important Safety Information ....................................3 Electrical Ratings ..................................................

this will ensure proper steaming characteristics by creating a thin layer of mineral deposits on the casting. caUtIOn all electrical connections must be in accordance with local electrical codes and any other applicable codes. warnInG electrIcal sHOcK HazarD. faIlUre tO fOllOw tHe InstrUctIOns In tHIs manUal cOUlD resUlt In serIOUs InjUrY Or DeatH. • electrical ground is required on this appliance. • Do not modify the power supply cord plug. If it does not fit the outlet, have a proper outlet in

(H)G BS-1365 - Fused, Permaplug 16 Amp, 250 VAC (Assembly Only) (H)I IEC-309, 16 Amp., 250 VAC., Pin & Sleeve (Assembly Only). AS3112 15 Amp., Australia (Harmonized Cord) Image Not Avaliable L Model Number Mfg. Number Volts Watts Amp Hertz ES-600HI 9300570 230 2900 12.6 50/60 ES-600HC 9300572 230 2900 12.6 50/60 ES-600 9300576 230 2900 12.6 50/60 ES-1200HI 9300580 230 2900 12.6 50/60 ES-1200HC 9300582 230 2900 12.6 50/60 ES-1200HG 9300584 230 2900 12.6 50/60 ES-1200 9300586 230 290 12.6 50/60 •

CAUTION Chlorides or phosphates in cleansing agents (e.g. bleach, sanitizers, degreasers or detergents) could cause permanent damage to stainless steel equipment. The damage is usually in the form of discoloration, dulling of metal surface finish, pits, voids, holes or cracks. This damage is permanent and not covered by warranty. The following tips are recommended for maintenance of your stainless steel equipment: • Always use soft, damp cloth for cleaning, rinse with clear water and wipe dry. W

To reset this thermostat, allow sufficient time (10-15 minutes) for the unit to cool down, then fully depress the reset button located at the rear of the unit (Figure 5). If the unit requires continuous resetting, contact your Roundup authorized service agency. CONVEYOR INTERLOCK SWITCH A conveyor interlock switch is located on top of the unit under the heat shield (Figure 4). The conveyors will not rotate unless the heat shield is in place and interlock switch is activated (depressed). Bun Thic

D 08/05 13 EGG STATION (ES-600 & ES-1200) 14 P/N 1010871 Rev. D 08/05 REPLACEMENT PARTS 18 21 11 3 27 14 18 31 13 28 65 16 25 51 53 59 61 60 24 19 5 55 4 58 14a 27 31 13a 28 65 45 45 48 48 66 54 63 52 62 57 56 69 2 7 26 29 15 1 12a 12 64 EGG STATION (ES-600 & ES-1200) REPLACEMENT PARTS (continued) Item Part Description Qty. Item Part Description Qty. No.No. 1 0021327 Nose Piece Weldment 1 42 308P143* Nut, Hex KEPS #8-32 1 2 210K230 Bumper, Recess Leg 1” 1 43 308P157* Screw, Tap #8-32 x 3/8” 1 (S

D 04/06 2 TABLE OF CONTENTS Owner Information .....................................................2 General ......................................................................2 Warranty Information .................................................2 Service/Technical Assistance ....................................2 Important Safety Information ....................................3 Specifications .............................................................4 Electrical Ratings ................

Steam coming out around top covers or sides. Generator Cover’s wingnut is loose. Tighten wingnut. Generator Cover is warped. Replace Generator Cover. 20 P/N 1010699 Rev. M 12/06 MIRACLE STEAMER TROUBLESHOOTING (continued) Problem Possible Cause Corrective Action Unit floods overnight and/or continues to steam even when in idle mode. Solenoid Valve is leaking due to debris trapped inside the plunger (MS-250/255). Attempt to flush the debris out of the valve by rapidly operating the unit on a numb

Nickel. MAINTENANCE (continued) Replacing the Optional Roller Tensioners 1. Remove the acorn nuts and old roller Tensioner Assembly (Figure 12). 2. Replace Tensioner Assembly, and reassemble. 3. Make sure the spacers are placed inside the Tensioner arm. The spacers are smaller than the holes to allow the Tensioner to pivot freely. Weld Screws Acorn Nuts Tensioner Assy. Spacers Teflon Tape Figure 12. Replacing Roller Tensioner Assy. Figure 14. Measuring Roller Tensioner Replacing the Spring Tensi