Q How do I clean the pan supports and burners? A Supports can be washed in the dishwasher or alternatively with a cream cleaner (such as Jif ) and a nylon scourer. Burners are best washed in warm water (see cleaning instructions on page 9). Q All the burners spark at once when I go to light one, is this ok? A Yes, they are designed to do this. Q Why doesn’t my cooktop light? A Firstly, check it is plugged in and the gas is turned on. Alternatively, the gas ignitors may be dirty. These are easily

Regular use of a stainless steel polish will reduce fingerprints and other marks. Heavy soiling can be removed with fume-free or heavy-duty oven cleaner (follow manufacturer’s instructions). Never use harsh/abrasive cleaning agents as they will damage the stainless steel finish. Chlorine or chlorine compounds in some cleaners are corrosive to stainless steel and may damage the appearance of your cooktop. Check the label on the cleaner before using. The graphics are etched onto the steel by laser

Cut hazard – When the safety cover is retracted, the blade in the scraper is razor-sharp. Use with extreme care and always store safely and out of reach of children. Do not use harsh/abrasive cleaning agents or heavy-duty scourers to clean your cooktop, as they may scratch the glass surface and damage the stainless steel finish and the knobs. Some nylon scourers may scratch the ceramic glass surface and damage the stainless steel finish and the knobs. Always read the label to check if your scour

Using your cooktop Lighting the cooktop Off 1 Choose the control knob for the burner you want to use. 2 Press the knob down gently and turn it anticlockwise to the High position. The electrodes on all the burners will High spark. Flame failure models only: Hold down the knob for approximately five seconds after the burner has lit. Releasing the knob too soon will extinguish the flame. Low Fig.4 Non-jet cooktop controls 3 Adjust the flame anywhere between the High and Low (knobs may vary from tho

GC36 GC912 & GC912M Adjusting the flame The flame adjusts anywhere between the Hi and Lo symbol. Do not regulate the flame between High and Off. Temperature control Your cooktop offers a wide range of temperature settings from delicate slow cooking to the intense high temperatures needed for boiling and searing. As the control knob is turned clockwise, the heat is increased. For general cooking purposes turn the control knob to the Hi setting to begin cooking or bring food to the boil and adjust

gal. liters 6.0 5.0 22.7 78 min.* 2 washes 3 rinses Short Wash For lightly soiled or pre-rinsed dishes and silverware. • Turn dial to SHORT WASH. • Select desired OPTIONS. gal. imp. gal. liters 4.8 4.0 18.2 71 min.* 1 wash 3 rinses Rinse/ Hold For rinsing dishes that will be washed later. • DO NOT USE detergent. • Turn dial to RINSE/HOLD. • Select SANITIZE OFF and HEAT DRY OFF. gal. imp. gal. liters 1.2 1.0 4.5 12 min. 1 rinse 750 Series Energy Options Hi-Temp Wash Option When HI-TEMP WASH ON op

If the burner does not remain lit, increase the minimum gas rate setting. To adjust the minimum gas rate setting: Turn on the burner. Turn the tap to the MINIMUM position. Take off the knob. With a small flat screwdriver turn the screw to the correct regulation. Note: for LPG gas, the regulation screw is normally tightened up. Fig. 10 Adjusting the minimum burner setting Table for the choice of injectors Natural gas 1.0 LPG gas 2.75Test Point Pressure [kPa] BURNER Injector Orifice Dia. [mm] Gas

By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product. Read and Save These Instructions Read all instructions before using this appliance. This Re

In this way, a patient airway temperature greater than 41 °C causes both heaters to be shut down. A watch dog failure, which is a high output from U5g, is communicated via isolating diode D11 and resistor R31 to the inverting input of U10c. This also ensures that both heater control circuits are clamped off in the event of a processor crash. 4.2.8 HEATERPLATE OVERTEMPERATURE Thermistor HP senses the heaterplate temperature. Should the heaterplate exceed the maximum heaterplate limit (default 110