A single beep will be heard to indicate initialization is completed. The above steps act as a reset. d. Power off the system power. Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: 1 2 3 4 5SW1 BZS EZ M2 M1 M0 1 2 3 4 5SW1 BZS EZ M2 M1 M0 SW1 SW1 1 2 3 4 5SW1 BZS EZ M2 M1 M0 RAID 5 Mode 1 2 3 4 5 SW1 BZS EZ M2 M1 M0 BZS EZ M2 M1 M0 RAID 1& RAID 10 Mode Large Mode 1 2 3 4 5 SW1 1 2 3 4 5 SW1 1 2 3 4 5 e. On the DIP switch, change (M0 to M2) setting to the desired RAID mode u

# Since USB 2.0 Hi-Speed is an evolution of the existing USB 1.1 specification, it is fully forward and backward compatible with current USB systems. # If your computer’s USB controller is only USB1.1 you can only achieve a 4X maximum CD writing speed. # If you do not have a USB2.0 port, you may install an optional USB2.0 adapter or controller (see optional accessories section on page 13) to your computer to achieve the maximum DVD CD writing speed. USB interface cable installation Attach the US

Insert the Gigabit Ethernet ExpressCard Adapter to the system’s ExpressCard slot. Windows 2000, XP & 2003 Driver Installations 1. The Found New Hardware Wizard pops on the screen. Place the Addonics driver disk into the CDROM drive. 2. Found New Hardware Wizard: Can Windows connect to Windows Update to search for software? Select “No, not at this time” Click Next. 3. The Generic Marvell Yukon Chipset base Ethernet Controller is identified. 4. Found New Hardware Wizard: What do you want the

ADSA4R-E (4-Port External SATA PCI Controller Card) SPECIFICATIONS INSTALLATIONS Chip Set: Silicon Image Sil3114 integrated host Controller Interface: PCI bus compatible I/O Ports: (4) eSATA Connectors Regulatory approvals: FCC, CE Features: • Up to 150 Mbytes/sec (1.5 Gbits/sec) per port • 4 External SATA (eSATA) ports with the new SATA External connector • Work with any SATA drive • Use as a non-RAID or RAID controller • Built-in RAID 0, RAID 1, RAID 1+0, RAID 1+ S support • Support la

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If the equipment does cause harmful interference to radio or television reception, which can b

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If the equipment does cause harmful interference to radio or television reception, which can b

A k. A ^ ■ I IL JÊL T E C H N O L O G I E S Master & Slave Pins Lever £ Pin 1 — Toshiba 1.8” ZIF (Zero Insertion Force) Hard Drive 1. Open the locking lever on the Toshiba 1.8” ZIF hard drive. 2. Slide the flat ribbon cable of the converter into the ZIF connector on the hard drive. 3. Close the lever to secure the ribbon cable connection. Connecting the Toshiba 1.8” ZIF hard drive to a 40-pin IDE connector AA25IDE35 (optional) Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-4

The Compact Flash should be keyed to prevent the card from being incorrectly inserted. 2. Put the mechanism in the open position and slide the flat ribbon cable into the ZIF connector on the adapter. 3. Close the latch to secure the ribbon cable connection. 1.8” ZIF- CF adapter shown below attached to a 1.8” ZIF to 2.5” IDE converter 1.8” ZIF- CF adapter shown below connected to a 2.5” drive enclosure TECHNICAL SUPPORT Email: Internet: Technical Support (8:30 am to 6:00 pm PST) Phone: 4

CardBus mode – move the switch to the side with the DOT indicator Text Box: Text Box: Text Box: CardBus Text Box: PCMCIA Text Box: Front view Text Box: Factory default setting is CardBus mode CardBus/PCMCIA driver Installation For Windows 95, 98, 98SE and Me (Do not run the SETUP program from the driver disk, SETUP Is for DOS or WIN 3.1 using PCMCIA mode only) 1. Power on your system and wait for the Desktop screen. 2. Connect the CardBus/PCMCIA cable and external AC/DC adapter into the back of

This will allow the NAS adapter to obtain its IP address automatically. If you prefer setting it manually, select the static IP option, enter your own value and click “Apply” to confirm the new setting. Disk Utility In this page, you can manage hard disk settings of the USB storage device. Format: For first time installation, you need to format hard disk into FAT32 file system. Formatting the drive will erase all data on the hard drive. Warning: For hard drives with data on it, be fore you have