LTD.LTD.LTD.LTD.LTD. will provide replacement parts free of charge during the will provide replacement parts free of charge during thewill provide replacement parts free of charge during thewill provide replacement parts free of charge during thewill provide replacement parts free of charge during thewill provide replacement parts free of charge during the first year of the limited warranty. first year of the limited warranty.first year of the limited warranty.first year of the limited warranty.

HORIZONTAL AIR TERMINAL INSTALLATION 4. Apply high temperature sealant W5730002 (not supplied) to the outer edge of the of the outside sleeve of the air terminal. Slip a 8" diameter coupler over the sleeve and secure as before. Trim the 8" coupler even with the 5" coupler end. 5. Thread the air terminal pipe assembly down through the roof support and attach, ensuring that a minimum 16" of air terminal FIGURE 29 FIGURE 27 will penetrate the roof when fastened. If the C CCA AAU UUL LLK KKI IIN NNG

La seriedad de estas lesiones o danos se clasifica segun los siguientes indicadores: ADVERTENCIA Este simbolo indica la posibilidad de muerte o una lesion grave. PRECAUCION Este simbolo indica la posibilidad de lesiones o danos a la propiedad. • Los significados de los simbolos que se utilizan en este manual se muestran como sigue: Nunca haga esto Siempre haga esto ADVERTENCIAS No exceda la capacidad de resistencia del tomacorriente o sistema de conexion electrico. • De lo contrario, se puede ca

2. To protect against a risk of electric shock, do not immerse the iron in water or other liquids. 3. The iron should always be turned to “Min” before plugging or unplugging from outlet. Never yank cord to disconnect from outlet; instead, grasp plug and pull to disconnect. 4. Do not allow cord to touch hot surfaces. Let iron cool completely before putting away. Loop cord loosely around iron when storing. 5. Always disconnect iron from electrical outlet when filling with water or emptying and whe

• Adults and especially children should be alerted to the hazards of high surface temperatures and should stay away to avoid burns or clothing ignition. Supervise young children when they are in the same room as the fireplace. • Clothing or other flammable material should not be placed on or near the fireplace. • Due to high temperatures, the fireplace should be located out of traffic and away from furniture and draperies. • Ensure you have incorporated adequate safety measure to protect infants

Be certain that your buffet is resting level on the countertop. There are 2 burner rings on this unit. NOTE: Avoid using pans that are unstable and easily tipped. 1. Place unit on a flat surface. NOTE: Be sure to leave 4 to 6 inches of space above and around the unit for proper ventilation. 2. Plug unit into electrical outlet. Turn Temperature Control Dials from OFF to selected setting (I = Low, II = Medium, III = High). The Indicator Light will glow when the burner is ON. CAUTION: Do not t

This reduces the waiting times (the iron takes less time to heat up than to cool down) and eliminates the risk of scorching the fabric. AUTOMATIC SHUT OFF The automatic shut off device trips after the iron has been left for approx. eight minutes in the upright position or unused for approx. Thirty seconds in the horizontal position. The light comes on to indicate that shut off has tripped. As soon as you move the iron, the device turns off and the iron starts working again. STEAM IRONING Filling

TABLE OF CONTENTS IMPORTANTSAFETYINSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . .3 SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 CYCLE TIMES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 COST OF OPERATION . . . . . . . . . . . . . . . . . . . . . . . .5 SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 CHANGING THE FILTER . . . . .

FIGURE 9a-c The fireplace requires a minimum enclosure height of 39”. For temperature requirements, the enclosure space around and above the fireplace must be left unobstructed. W415-0298 / K / 12.06.07 FINISHING HOODGRATE AND LOG INSTALLATION FINISHING HOODGRATE AND LOG INSTALLATION 1. Remove curtain mesh and rod assembly 2. Remove log carton 3. Remove grate from the lower control area (stored there when shipped) 4. Unscrew the 3 screws in the firebox, set grate in place and secure using the 3

INSIDE: Attach and secure the flex liners to the vent connection assembly using the same procedure as before, ensuring that the marked exhaust liner is attached to the exhaust collar. FIGURE 3 FIGURE 4 VENT CONNECTOR EXTENSION RESTRICTOR PLATE STUDS FIGURE5a-b 5. Reaching in through the insert, manoeuvre the vent connection assembly through the openings in the firebox top, taking care not to damage the gasket. In case of a low ceiling fireplace, the extension should be removed and reinstalled af