No. Engine Serial No. (E/No) Model No. Serial No. The Serial No. plate is located on the right side of the console. For ease of ordering and reference, we suggest that you record the information requested. Place Model No. And Serial No. Label Here (Included in Literature Pack) or Fill in Below ® For Serial Nos. 720,000 & Higher Part No. 4500-303 Rev. A EXMARK PARTS PLUS® PROGRAM EFFECTIVE DATE: September 1, 1995 Program If your Exmark dealer does not have the Exmark part in stock, Exmark will ge

4.1.11 Drive Wheel Release Valves: Located on the top right front corner of hydrostatic pumps. Drive wheel release valves are used to release the hydrostatic drive system to allow the machine to be pushed without the engine running. Tilt seat up to gain access to pumps. With a 5/8 wrench, turn both valves one turn counter-clockwise to release drive system. Turn clockwise to reset system. DO NOT overtighten. DO NOT tow machine. 4.1.12 Coolant Temperature Gauge: Located at the front of the left fu

Checks before each operation: Before use, an inspection is always to be performed In order to determine that all nuts, bolts and working tools are not worn down or damaged. Worn down or damaged blades are to be replaced in sets. Inspect the surface on which the lawn mower is to be used be-forehand. Stones, pieces of wood and wires as well as other solid matter are to be removed. Objects, which are contacted bythe cutting tools, could be thrown out uncontrollably. Proper use / Responsibility Warn

Exmark black touch up spray paint - Gloss black 5 MAIN FRAME GROUP (cont.) 6 REAR FRAME GROUP Item Part No. Description Qty. 1 1-513746 Decal, Muffler................................. ........2 2 1-543508 Cup, Bearing Tapered Roller.......... ........4 3 1-543509 Cone, Bearing Tapered Roller........ ........4 4 1-543511 Seal, Grease.................................. ........2 5 1-633508 Washer, Spring Disc ...................... ........6 6 1-633585 Bearing, Cone Tapered Roller.......

3. Unscrew the tightening nut 0, adjust the handle A to the correct length and tighten the nut 0 by hand. 4. Press and hold down the adjusting button B, set the cutting head 7 to the correct angle, then release the adjusting button B. 1. Press the start button C on the handle 3. The Turbotrimmer starts. 2. Release the start button C on the handle 3. The Turbotrimmer switches off. 1. For vertical cutting, loosen the tightening nut 8, turn the additional handle 6 180° and then tighten the nut 8 ag

lbs. (136 N-m). b) Further tighten the nut until the next set of slots line up with the cross hole in the shaft. c) Replace cotter pin. Note: Do not use anti-seize compound on the wheel hub. 5.1.21 Thread locking adhesives such as “Loctite 242” or “Fel-Pro, Pro-Lock Nut-Type” are used on the following fasteners: a) Pump drive sheave setscrews. b) Square head setscrews on Hydro pump control arms. c) Shoulder bolts in ends of speed control crank. e) OPC lever setscrews. f) Electric clutch retainin

1 7 109-7335 Asm, Hoc Plate W/Decal........... ........... 1 7:2 116-0752 Decal, Cut Of Height.................. ........... 1 8 109-8250 Grip, Lever................................. ........... 1 Item Part No. Description Qty. 1 62-1330 Bolt-Shoulder.......................... .............. 1 2 109-7130 Grommet................................. .............. 1 3 104-8301 Nut, Nyloc 3/8-16 Flg.............. .............. 1 4 109-7124 Spring, Extension.................... ..............

103-9259 Harness, Wiring ....................................1 Item Part No. Description Qty. 22 1-303287 Plastic Tie, Small .................................. 2 23 1-543393 Insulator, Solenoid (+)............................ 1 24 1-643275 Relay, 12 V............................................ 2 25 1-803075 Screw-head, Truss [#10-24X.75]............ 2 26 103-5685 Asm, Seat Switch Actuator .................... 1 27 1-543286 Grommet ............................................... 2 28 1-633396 Cl

1 26 1-633396 Clip-Loom .69 .................... 3 7 3256-2 Washer, 1/4 flat.................. 2 27 103-0732 Harness-wiring................... 1 8 32128-20 Nut, 5/16-18 whizlock ......... 2 28 1-303335 Plastic tie (large) ................ 2 9 1-523415 Spring-seat switch.............. 1 29 1-523281 Cable-battery (+) 30”.......... 1 10 1-522424 Spring mount wldmt ........... 1 30 1-543393 Insulator, solenoid (+) ........ 3 11 321-4 Screw, 1/4-20x3/4 .............. 8 31 1-633651 Bolt, battery hold

2.6.2 Mounting: Hinged to tilt up for access to hydraulic pumps, battery and other components. The seat is held in the tilted position with a linkage. Adjustable fore and aft seat track. 2.6.3 Seat Safety Switch: Internal to the bottom seat cushion, non serviceable. Time delay module incorporated into the Safety Interlock System eliminates rough ground cut-outs. 2.6.4 Armrests: Standard seat: foam padded flip-up armrests. Optional suspension seat: molded adjustable flip-up armrests. 2.7 HYDROSTA