• If required, the plunge depth can be set accurately to within 0.1 mm. • Retighten button 9. Adjustment using the revolver- depth stop The revolver-depth stop enables you to quickly choose between six different cutting depths. These are also determined by the adjustment of the depth stop (10). • Adjust the required cutting depth by rotating the revolver-depth stop (21). Helpline No. UK / Northern Ireland 0870 7323023 • Rep. Ireland 1800 481005 Web Support: Model Number: PBF-1200 15 Helpline No.

Normal system filtrsitions should be sufficient. Systems which do not have any filtration should be equipped with at least a 200 m6sh sjeve or 74 micron filter. Most hydraulic systems would already have a much finer filtration. Within the cartridge dirt or sealing agents, such as Teflon tape, may lodge within and cause malfunction. If a malfunction does occur and you are using proper filtration, we would recommend disassembly and cleaning. This Can be done as follows: On clean bench, remove sm

INSTALLING.....................................................................................................................................4 2.1 LAYOUT...........................................................................................................................................4 2.2 JUMPER SETUP..................................................................................................................................5 2.2.1 JP0 ~ JP15 Analog Input R/C Filter ...............

Rectangular shaped metal liner available for on-site Wood Hood construction, Figure 4. 4. The ventilation system (power module and ducting system) is not included and must be purchased separately. B. Installation: Metal Liner - T-Shaped, Figure 3 1. Measure up 6 1/8 from the bottom of adjacent cabinets. Scribe a level line horizontally across depth of both cabinets. 2. Raise Metal Liner so that bottom edge of liner is level with scribed lines. Use four (4) #8 x 1/2” screws provided to attac

6.2.1 Pumping in the FLOW RATE Mode To pump fluid in the FLOW RATE Mode, do the following: 1. Set up the pump motor for pumping, according to Chapter 3. 2. Toggle the ON/OFF switch to turn on the unit’s power. The display is in the STOPPED Display Mode. Refer to Figure 6-3. 3. Either set the TUBE ID for the tube you are using (following Section 5.3) or calibrate the tube (following Section 5.5), before continuing. 4. Press the FLOW RATE key. FLOW RATE Display shows xxx mL/min ACTION Displays cur

Box 4047 ISO 9001 Certified Stamford, CT 06907-0047 TEL: (203) 359-1660 FAX: (203) 359-7700 e-mail: info@omega.com Canada: 976 Bergar Laval (Quebec) H7L 5A1 TEL: (514) 856-6928 FAX: (514) 856-6886 e-mail: info@omega.ca For immediate technical or application assistance: USA and Canada: Sales Service: 1-800-826-6342 / 1-800-TC-OMEGA® Customer Service: 1-800-622-2378 / 1-800-622-BEST® Engineering Service: 1-800-872-9436 / 1-800-USA-WHEN® TELEX: 996404 EASYLINK: 62968934 CABLE: OMEGA Mexico: (001) 8

This is done by using four connecting leads to the device and connecting the V+ and I+ leads to the anode and the V– and I– leads to the cathode as shown in Figure 1. The exact point at which the connecting leads are soldered to the device leads results in negligible temperature measurement uncertainties. In a two-wire measurement configuration, the voltage connections (point A in Figure 1) are made near or at the current source, so only two leads are actually connected to the device. Some loss

COMMUNICATION PARAMETERS: This is one byte data and specifies BAUD, PARITY, DATA, and STOP bit. BAUD = bits 2,1,0 are: 000-001 not used 010 for 1200 011 for 2400 100 for 4800 101 for 9600 110 for 19200 111 not used Page 12 PARITY = bits 4,3 and are: 00 for NO 01 for ODD 10 for EVEN 11 not used DATA BIT = bit 5 and is: 0 for 7 data 1 for 8 data STOP BIT = bit 6 and is: 0 for 1 stop 1 for 2 stop Bit 7 : always 0 Note 1: Stop bit is always 1. Unless 7 data, no parity is selected then unit will use

To use the RS485 communication for the Signal Conditioners you’ll need an available Communication port in your computer and have access to a generic communication software program (e.g.: Procomm1, Windows2 HyperTerminal3, etc, see details below for information). A RS485 signal conditioner communication software program is also available as an option to speed the set-up. A RS232 to RS485 converter box will also be required if your computer communications port is RS232. 1 Procomm is a registered t

Box 4047 ISO 9001 Certified Stamford CT 06907-0047 TEL: (203) 359-1660 FAX: (203) 359-7700 e-mail: info@omega.com Canada: 976 Bergar Laval (Quebec) H7L 5A1 TEL: (514) 856-6928 FAX: (514) 856-6886 e-mail: info@omega.ca For immediate technical or application assistance: USA and Canada: Sales Service: 1-800-826-6342 / 1-800-TC-OMEGA® Customer Service: 1-800-622-2378 / 1-800-622-BEST® Engineering Service: 1-800-872-9436 / 1-800-USA-WHEN® TELEX: 996404 EASYLINK: 62968934 CABLE: OMEGA Mexico: TEL: (00