Since signal detect works on light energy alone, there does not need to be valid data on the fiber receiver for there to be an output from the transmitter. If there is valid data present on the fiber receiver, it is copied to the fiber transmitter. This preserves data transparency but not necessarily protocol transparency. The outgoing protocol is always serial FPDP. AGE1439_FIBER_MODE_RAW transmits unprocessed and unbuffered ADC data over the fiber interface. After selection, optical data trans

5 Steps to Install the 82357A............................................................ 7 Step 1: Before You Install the 82357A........................................... 8 Check Your Shipment ............................................................ 8 Check System Requirements ................................................. 9 Step 2: Installing Agilent IO Libraries Suite ................................. 10 Checking for Installed Agilent IO Libraries ........................... 10 Instal

Since errors from each component are not correlated with each other, the total system error will be the root-sum-square (RSS) of all the errors: 2 ETOTAL 2 = EDAQ 2 + ESIG_COND 2 + ETHERMOCOUPLE Example: Assume the following conditions: • DAQ: Agilent U2355A • Signal Conditioning: Agilent U2802A • Ambient temperature: 23 °C • Thermocouple type: J-type, standard limits of error • Temperature to measure: 600 °C Assume the following error specifications: • U2355A: Gain error = 0.02% of reading • Of

• For more information, refer to the AMM Help File, Chassis Trigger page. U2781A User’s Guide Features and Functions To PC with AMM USB Interface MASTER Module MASTER Module SSI Signals SSI Signals FPGA FPGA 55-pin 55-pin 55-pin Connectors 55-pin 55-pin 55-pin 55-pin 55-pin Connectors Connectors Connectors Connectors Connectors Connectors Connectors SSI Trigger Bus Chassis SLAVE module 1 SLAVE module 1 SLAVE module 2 SLAVE module 2 SSI Signals SSI Signals FPGA FPGA 55-pin 55-pin Connectors Conne

Multiplexer 34922A Simplified Schematic 34922A D-Sub Connectors 34922T Terminal Block 34923A 40/80-Channel Reed Multiplexer 34923A Simplified Schematic for Two- or Four-Wire Mode 34923A D-Sub Connectors for Two- or Four-Wire Mode 34923T-001 Terminal Block for Two- or Four-Wire Mode 34923A Simplified Schematic for One-Wire Mode 34923A D-Sub Connectors for One-Wire Mode 34923T-002 Terminal Block for One-Wire Mode 34924A 70-Channel Reed Multiplexer 34924A Simplified Schematic 34924A D-Connectors 34

At least 4Gb or higher. The USB cable is an Addonics USB 2.0 interface cable. The process involved A. Set up the USB drives under DOS mode (step 1 - 9) B. Copy folders and files from your Windows installation CD to the hard drives (step 10 - 17) C. start the software installation Installing Windows 2000, XP, 98SE or Me using the Addonics USB CD-ROM, DVD-ROM, DVD/CDRW or DVD-R/RW drive. 1. Download USB DOS driver and Save the file to your hard drive. 2. Use Winzip to extract the file, if you do n

• The test set and associated equipment are connected as shown in Figure 2-9 on page 2-15. This chapter shows you how the network analyzer can be used to manually control the test set. The method presented here is considered a manual one because the user manually enters individual commands on a keyboard connected to the network analyzer. The chapter includes the following sections: • Preparing the Analyzer to Control the Test Set • How to Send a Manual Command • Common Errors in Manual Commands

re the ribbon cable connection. 1.8” ZIF- CF adapter shown below attached to a 1.8” ZIF to 2.5” IDE converter 1.8” ZIF- CF adapter shown below connected to a 2.5” drive enclosure TECHNICAL SUPPORT Email: Internet: Technical Support (8:30 am to 6:00 pm PST) Phone: 408 433-3855 Email: http://www.addonics.com/support/query/

This will enable this folder as the shared folder. In the example below “PUBLIC” is Share directory. Same procedure applies for the Music and Video folders. On your Xbox 360, go to “Media” tab, select either Music or Pictures and press A button of the Xbox console to continue. Press X button of the Xbox console to change the source and select your network drive. It should show up as storagexxx and display the folder that you have set up earlier on your NAS adapter. Printer Server Inside the shar

Connecting a Printer: •Connect a printer to print a hardcopy of the test results if required. Inserting the TEST SIM for GSM mobile phone or TEST USIM for a W-CDMA mobile phone: •Insert the Test SIM (Subscriber Identity Module) supplied by Agilent into the GSM mobile phone or the test USIM (Universal Subscriber Identity Module) supplied by Agilent into the W-CDMA mobile phone before performing any test. •GSM/W-CDMA/cdma2000 Mobile Phone Repair Process Figure 3-2 Mobile Phone Repair Process 4 GSM