! Warning! To reduce the risk of fire and burn injury, use only spark plugs authorized by STIHL. Always press spark plug boot snugly onto spark plug terminal of the proper size. (Note: If terminal has detachable SAE adapter nut, it must be attached.) A loose connection between spark plug terminal and ignition wire connector in the boot may create arcing that could ignite combustible fumes and cause a fire. Keep spark plug clean, and make sure ignition lead is in good condition. ! Warning! Do not

Installing Weld Curtain £k 1 Weld Curtain Frame 2 Turntable Top 3 Capscrews 4 Weld Curtain 5 Support Bars I nstall weld curtain frame on turntable top with four capscrews. Position weld curtain in curtain frame and install support bar through frame and curtain. 3-8. Installing Input/Output Cable To Robot Use receptacle to connect input/ output cable to robot. 1 Receptacle RC1 2 Keyway 3 Plug 4 Threaded Connector To connect input/output cable to robot, align keyway, insert plug, and

This Operator's Manual is an integral part of the safe operation of this machine and must be maintained with the unit at all times. READ, UNDERSTAND, and FOLLOW the Safety and Operation Instructions contained in this manual before operating the equipment. If the Operator's Manual is not with the equipment, contact your dealer or Servis-Rhino (800446- 5158) to obtain a Free copy before operating the equipment. ALAMO INDUSTRIAL 1502 E. Walnut Seguin, Texas 78155 210-372-3551 © 2008 Alamo Group Inc

SAFETY PRECAUTIONS . READ BEFORE USING . . . . . . . . . . . . . . . 1 SECTION 2 . SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 SECTION 3 . OPERATION INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 SECTION 4 . BATTERY REPLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 SECTION 5 . MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Verify left and right battery trays are installed on the correct sides. Not switching – auto-lens stays light and does not darken when welding or cutting. Stop welding or cutting immediately: Make sure the lens is turned On. If power is On, check the mode settings. Also review sensitivity recommendations and adjust sensitivity if possible. Clean lens cover and sensors of any obstructions. Make sure the sensors are facing the arc; angles of 45 or more may not allow the arc light to reach the sens

Automatically enhances Stick welding, especially on pipe, by focusing the arc and preventing the electrode from going out. Optional AC/DC/battery charge/ jump-start for AC TIG welding and 12 or 24 volt batteries. Simply select the battery voltage and connect cables to the separate battery output studs. (High-frequency unit required for AC TIG.) Hot Start™ electrode starts to make it easy to start all types of electrodes. allows air flow to cool and prolong the life of the engine. Also reduces so

HOT PARTS can cause severe burns. . Do not touch hot parts bare handed. . Allow cooling period before working on gun or torch. . To handle hot parts, use proper tools and/or wear heavy, insulated welding gloves and clothing to prevent burns. OM-278 Page 1 FUMES AND GASES can be hazardous. Welding produces fumes and gases. Breathing these fumes and gases can be hazardous to your health. . Keep your head out of the fumes. Do not breathe the fumes. . If inside, ventilate the area and/or use local f

Lift up drive roll swing arms. Install PD inlet guide. Do not tighten set screw to secure inlet guide. Set screw may be used to secure PD inlet guide replacements such as wire straighteners or conduit adapters. Remove screw securing intermediate guide holder. (Guide holder is located between the lower front and rear drive roll carriers.) Rotate guide holder 180 degrees and reinstall. Install intermediate guide into guide holder and tighten set screw. Loosen set screw, insert exit guide into bl

DMG EFD Remote control circuit common. EF E 0 to +10 volts dc output signal from wire feeder to power source with respect to socket D. H Voltage feedback; 0 to +10 volts dc, 1 volt per 10 arc volts. F Current feedback; 0 to +10 volts dc, 1 volt per 100 amperes. *The remaining pins are not used. 4-4. Gun Recommendation Table Process Gun GMAW – Hard or Cored Wires Roughneck C-Series Guns: 300, 400, 500, And 600 Amp. FCAW – Self-Shielding Wires FC-1260 Or FC-1150 4-5. Wire Type, Size, And Feed Spee