ATTENTION: Exhaust hood operation may affect other vented appliances; in each case it shall be installed in conformity with the national standards in force. 2 INSTALLATION MANUAL BACKGUARD INSTALLATION INSTRUCTION Please follow the following installation instructions afther installing the cooktop: 1) Remove n°2 screws fixing worktop as shown in fig.1 2) Place front part of the backguard and attach it from bottom side with the two removed screws (point 2) as shown in fig .2 3) Fix the front part

Follow the gas supplier’s instructions. - If you cannot reach your gas suppliers, call the fire department. Installation and service must be performed by a qualified installer, service agency or the gas supplier. 310200 WARNING Read this instruction booklet before installing and using the appliance. The manufacturer will not be responsible for any damage to property or to persons caused by incorrect installation or improper use of the appliance. The manufacturer reserves the right to make change

The amount of smoke stain is directly related to the amount of food residues in the oven cavity before the start of the self.cleaning cycle. Before Self Cleaning the Oven Wipe out large spillages, grease and any loose soil that can be easily removed. Remove any soil that is outside the door seal area. This appliance is designed to clean the oven interior and the portion of the door that faces the oven cavity. The outer edges of the door and the oven cavity are not in the cleaning zone. Wipe this

BAKEWARE TYPE Metal bake ware (with or without a non.stick finish), heat.proof glass, glass ceramic, pottery, or other utensils are suitable for the oven. Suitable cookie sheets have a small lip on one side only. Heavy sheets or those with lips on more than one side may affect the baking time. BAKE RACK POSITIONS Rack level positions in the oven are numbered as in the diagram on page 25. ONE RACK BAKING . The Bake mode is best for baking on one rack with rack level 3 and 4 used for most baked it

To convert the regulator for use with other liquid propane LP gas: 1. Unscrew by hand the upper cap of the regulator, remove the white plastic attachment from the cap, reverse its direction and screw it again firmly against the cap. The white plastic attachment has arrows indicating the position for natural gas (NAT) and LP gas (LP). 2. Screw by hand the metal cap in the original position on the regulator. 19 STEP 2: SURFACE BURNERS To replace the nozzles of the surface burners, lift up the burn

35 SELF.CLEANING THE OVEN ..................................................................................................................................... 35 MAINTAINING YOUR RANGE.................................................................................................................................. 36 CLEANING YOUR RANGE ........................................................................................................................................ 36 TROUBLESHOOTING GUIDE

The minimum gas supply pressure for checking the regulator setting shall be at least 1“ w.c. (249 Pa) above the inlet specified manifold pressure to the appliance (this operating pressure is 4” w.c. (1.00 kPa) for Natural Gas and 11” w.c. (2.75 kPa for LP Gas). 9 INSTALLING THE LEGS INSTALLING THE WORKTOP Bertazzoni ranges must be used only with the legs properly installed. Four height.adjustable legs are shipped with the range in the polystyrene container situated over the appliance. Before ins

Open the valve on the gas supply. Using a soap and water solution check each gas connection one at the time, by brushing the solution over the connection. Presence of bubbles will indicate a leak. Tighten the fitting and recheck for leaks. If it is not possible to correct the leak, replace fitting. Under no circumstances use matches or flame for checking leaks. It is essential that the gasket and the pressure test point stopper are properly installed to avoid gas leakage Fig.5B Inches mm A 1 9/1

3 IMPORTANT SERVICE INSTRUCTIONS ....................... 3 DESCRIPTION ....................... 4 UNPACKING & WARRANTY ....................... 5 INSTALLATION NOTES ....................... 5 FRONT VIEW ....................... 6 REAR VIEW ....................... 7 INPUT A / INPUT B ....................... 7 PARALLEL CONNECTION ....................... 7 DSP OUT ....................... 7 CONTROL PORT ....................... 7 RS-232 INTERFACE ....................... 8 ADDRESS .......................

Operating in this way the gas regulator is converted for use with the other gas/pressure. Service & maintenance instructions Service and maintenance only to be carried out by an authorised person To replace parts such as burners, valves and electric components, the hotplate must be removed from the bench top by releasing the attachment hooks, loosening the attachment screws of each burner, unscrewing the hotplate attachments nuts which are visible at the bottom of the surface, removing the hotpl