Do not apply this product or allow it to drift to blooming crops or weeds while bees are actively visiting the treatment area. YARD SHIELD CHEMICAL CONCENTRATE FIRST AID IF SWALLOWED: •Immediately call a poison control center or doctor. •Do not induce vomiting unless told to do so by a poison control center or doctor. •Do not give any liquid to the person. •Do not give anything by mouth to an unconscious person. IF IN EYES: 20 minutes.–•Hold eye open and rinse slowly and gently with water for 15

As a precaution, store fuel in an approved, airtight container. Store in a well-ventilated, unoccupied building, away from sparks and flames. IMPORTANT Stored fuel ages. Do not mix more fuel than you expect to use in thirty (30) days, ninety (90) days when a fuel stabilizer is added. Stored two-stroke fuel may separate. ALWAYS shake fuel container thoroughly before each use. SM T W T F S 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 31 30 14 OPERATION -Provide all

Some believe that prolonged exposure to vibration may contribute to CTS. CTS can cause severe pain for months or even years. To reduce the risk of RSI/CTS, do the following: • Avoid using your wrist in a bent, extended or twisted position. Instead try to maintain a straight wrist position. Also, when grasping, use your whole hand, not just the thumb and index finger. • Take periodic breaks to minimize repetition and rest your hands. • Reduce the speed & force in which you do the repetitive movem

Know and understand the location and operation of the controls. Also pay close attention to safety messages in this manual. IMPORTANT Unauthorized modifications to the pump may impair the function and/or safety and affect machine life. Use only approved accessories on the pump. DANGER Do not let anyone operate the pump without proper instruction, otherwise serious personal injury may result. Do not pump flammable substances with this pump. Do not pump corrosive chemicals with this pump. Exposure

The spark arrestor screen prevents hot, glowing particles of carbon from leaving the muffler. Keep exhaust area clear of flammable debris. 2. CARRyING hANDLE - The carrying handle is used to transport the pump. 3. sPARk PLUG - Provides spark to ignite fuel mixture. 4. ChOkE LEVER - Choke lever is located at the top of the air cleaner. - Move choke forward to CLOSE (Starting Position) ( ) -Move to OPEN (Run Position) ( ) 5. AIR CLEANER -Contains replaceable felt element. Should be inspected and c

See "Carburetor Adjustment" in the unit Operator's Manual. * WARNING! DO NOT INSTALL BLADES ON GT (CURVED SHAFT) MODEL TRIMMERS ** Arbor diameter of Upper Blade Plate must match arbor diameter of metal blades. *** New cotter pin required each time blade is installed. **** Brushcutters over 16.5 lbs (7.5 kg) dry weight (weight w/o fuel) require a double shoulder harness contents 1 U-handle assembly 1 Lower u-handle bracket (2 halves) 1 Harness clamp w/ring 1 5 x 12 mm bolt 1 8 x 55 mm bolt 1 Circ

2. Desconecte el cable de parada de ignicion (A) y (B). 3. Afloje tuercas (C) y retire la mensula para el cable del acelerador. 4. Retire el cable del estrangulador interno del balancin del carburador (D). 5. Afloje los dos (2) pernos (E) de las abrazaderas del eje de impulsion del motor, y quite el perno de ubicacion del eje de impulsion central (F). 6. Extraiga el conjunto del eje motriz de la caja del embrague. 7. Afloje los (2) tornillos (G) del asa trasera y extraiga el asa trasera del conj

19. Check throttle for freedom of movement and that wide open throttle / low idle extremes are adjusted properly. If adjustment cannot be achieved with adjusting nuts (C), consult with your Echo Dealer for correct adjustment procedure. Tighten nuts (C). 20. Connect 2 ignition stop leads (A,B) from throttle cable tubing to 2 ignition leads (A,B) on engine. 21. Gather ignition wires and position behind air filter case. 22. Install air filter and cover Install Hip Pad (Optional) 1. Attach hip pad t

8. Install the spark plug (do not connect ignition cable). 9. Remove blower pipe assembly from unit. SERVICING INFORMATION SERVICING INFORMATION Genuine ECHO Parts and ECHO Re Power Parts and Assemblies for your ECHO products are available only from an Authorized ECHO Dealer. When you do need to buy parts always have the Model Number, Type number and Serial Number of the unit with you. You can find all three numbers on the engine housing. For future reference, write them in the space provided be

System Start-up: (purging air from system). Factory Fills unit with SAE 20W-50 multiviscosity motor oil. This will need to be checked when setting up with instructions below. At system start-up, several things need to be accomplished to ensure a properly running system. 1. Fill the BDU case and expansion level and ensure they do not empty during the following procedure. 2. Start engine and increase throttle to at least 2/3 speed. 3. Open bypass valve by depressing bypass plunger and holding. 4.