• The outer shell of the AIE2 is transparent to IR so that hand-held remotes can be used even if the emitter is covering the component’s IR receiver. 2 Typical Installation To 120V AC (unswitched) PS2 Power Supply A/V Receiver Satellite DVD AIR6 In-Wall IR Receiver AIE2 Talk-Back Emitter Rear View ConnectionTerminalsAIE2 Talk-Back Emitter AIE2 Talk-Back Emitter AIB4 Amplified IR Connection Block Caution: Do not plug the AIE2 into an emitter jack that is set to HIGH Power or “Blaster as this will

THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESSED AND IMPLIED WARRANTIES. ATON EXPRESSLY DISCLAIMS ALL SUCH OTHER WARRANTIES, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. Notwithstanding the above, where applicable, if you qualify as a “consumer” under the Magnuson-Moss Warranty Act, then you may be entitled to any implied warranties allowed by law for the Warranty Period. Some states do not allo

This application provides the best sound quality, staging, and depth possible in areas with a defi ned listening position. Figure 2.1 shows an example of a stereo listening area. X Figure 2.1 - Stereo Application Home Theater ATON IN-wall Speakers provide unobtrusive, high-quality Home Theater sound when installed in the correct locations. It is critical to identify the primary listening position before installation! See Figure 2.2 for a system design utilizing in-wall speakers with an active su

Note: A stud-fi nding device may not detect pipes, wiring, or other obstructions located behind the drywall. 2. Use the inside portion of the speaker cutout template (included in packaging) to confi rm speaker placement. 3. Remove templates and drill or carefully punch a pilot hole in the wall. A bent piece of wire or a coat hanger may be use to probe the stud bay for obstructions. If you experience resistance of any kind–STOP! If any obstructions are detected, patch the pilot hole and try again

100 Watts Cutout Dimensions ................................................................................................. 7-1/8" x 12-1/4" (181mm x 311mm) Outer Frame Dimensions ................................................................................ 8-5/8" x 13-13/16" (218mm x 351mm) Mounting Depth ...............................................................................................................................................3-3/4” (94mm) Pre-Construction Bracket .....

75 Watts Cutout Dimensions ................................................................................................. 7-1/8" x 12-1/4" (181mm x 311mm) Outer Frame Dimensions ................................................................................ 8-5/8" x 13-13/16" (218mm x 351mm) Mounting Depth ............................................................................................................................................ 3-5/16” (83mm) Pre-Construction Bracket .......

If you must cross high-voltage lines, always do so at a 90 degree angle to avoid audible hum through the speakers!. Note 3: When pre-wiring for In-wall speakers, it is essential to make direct wire runs from the head-end to each speaker. Do not run speaker wires in series or parallel, and do not “daisy-chain” speakers to common wiring. ©2007 • All rights reserved. © 2007 • All rights reserved. 7 Storm Series In-wall Speakers Pre-Wiring The audio/speaker cable runs should be routed from the head-

Features excellent bass response, accurate highs and ultra-smooth mids. Model 062 Delivers the same exceptional sound of a pair of O62s in a single location speaker. Utilizes a dual voice coil woofer and tweeter to deliver audio in areas where two separate speakers are not practical or desired. ww ww oo M O Provides big outdoor sound at a great price point. Features low, powerful bass, warm mids and open, airy highs.oo M 0 Technology in reach.™ OUTDOOR SPEAKERS OUTDOOR SPEAKER FEATURES All-weath

ww ww oo M O Provides big outdoor sound at a great price point. Features low, powerful bass, warm mids and open, airy highs.oo M 0 Technology in reach.™ OUTDOOR SPEAKERS BUILT TO WEATHER THE STORM Constructed and tested to withstand the harshest outdoor conditions, The ATON™ Storm Series Outdoor Speakers are guaranteed to provide years of reliable outdoor use. Each model’s all-weather cabinet design effectively shields the speaker from the elements and makes the speaker ideal for any outdoor app

Each model’s all-weather cabinet design effectively shields the speaker from the elements and makes the speaker ideal for any outdoor application. But the test of a great outdoor speaker is more than its durability. It has to deliver high quality sound in an environment very different from indoor applications. As a result, all Storm Series Outdoor Speakers are voiced to provide adequate sound pressure levels and deliver big, indoor-quality sound even in outdoor, open-air conditions. UNPARALLELED