• Avoid creating a source of ignition for spilled fuel. Do not start the engine until fuel vapors dissipate. • Always stop the engine and allow it to cool before filling the fuel tank. Never remove the cap of the fuel tank, or add fuel, when the engine is hot. Never operate the unit without the fuel cap securely in place. Loosen the fuel tank cap slowly to relieve any pressure in the tank. • Mix and add fuel in a clean, well-ventilated outdoor area where there are no sparks or flames. Slowly rem

10). 5. Pull the starter rope briskly 5 times. 6. Place the blue choke lever in Position 2. 7. Pull the starter rope briskly 1 to 3 times to start the engine. 8. Allow the engine to warm up for 15 to 30 seconds. 9. Place the blue choke lever in Position 3. The unit is ready for use. IF... The engine does not start, go back to step 2. IF... The engine fails to start after a couple attempts, place the blue choke lever in Position 3 and move the throttle control to the fast position ( ). Pull the s

You will find it to be a great labor-saving device. This operator's manual provides you with easy-tounderstand operating instructions. Read the whole manual and follow all the instructions to keep your new outdoor power tool in top operating condition. PRODUCT REFERENCES, ILLUSTRATIONS AND SPECIFICATIONS All information, illustrations, and specifications in this manual are based on the latest product information available at the time of printing. We reserve the right to make changes at any time

Fingers may become trapped between split wood. 1. To remove partially split wood from wedge, move control handle to REVERSE position until wedge is fully retracted to allow split wood portion to contact the log dislodger. 2. Once removed from wedge with log dislodger, split wood from opposite end or in another location. Vertical Position 1. Pull the horizontal beam lock out to release the beam and pivot the beam to the vertical position. 2. To lock the beam in the vertical position, pull out on

4. Water or dirt in fuel system. 5. Dirty air cleaner. 6. Carburetor out of adjustment. 1. Connect and tighten spark plug wire. 2. Move choke lever to OFF position. 3. Clean fuel line; fill tank with clean, fresh gasoline. 4. Drain fuel tank. Refill with fresh fuel. 5. Clean or replace air cleaner. 6. See authorized service dealer. Too much vibration 1. Loose parts or damaged impeller. 1. See authorized service dealer. Engine overheats 1. Engine oil level low. 2. Dirty air cleaner. 3. Carburet

Nozzle Height Adjustment The nozzle can be adjusted to any five positions, ranging from 5/8” to 4 1/8” ground clearance. The nozzle height has to be adjusted according to the conditions. Move the height adjustment levers forward or backward to adjust the nozzle upwards or downwards. See Figure 8. NOTE: In general, raise the nozzle height to vacuum a thick layer of leaves or to operate with the blower chute and lower the nozzle height for smoother surfaces. Figure 8 SECTION 5: MAINTAINING YOUR CH

770-10574A.fm (8/01) IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY MTD PRODUCTS INC. P.O. BOX 368022 CLEVELAND, OHIO 44136-9722 Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forestcovered, brush-covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working orde

24645-9 Important: Read Safety Rules and Instructions Carefully vaRD-MaN 8 H.P. DELUXE LOG SPLITTER PRINTED IN U.S.A. _/ FORM No. 770-8316 LIMITED WARRANTY For one year from the date of original retail purchase,YARD MAN COMPANY will either repair of replace, at its option, free of charge, F.O.B. factory or authorized service firm, any part or parts found to be defective in material or workmanship. Transportation charges under this warranty must be paid by the purchaser unless return is

Throttle Lever On/Off Switch Handle Connectors Primer Starter Handle Front Handle Cultivator Choke Lever Edger Wheel Edger Blade Tines 7 • Remove the oil plug/dipstick from the crankcase and pour the entire bottle of oil into the oil fill hole. See Figure 3. • Wipe up any oil that may have spilled and reinstall the oil fill plug/dipstick. Figure 3 Gas Fill-Up Old fuel is the primary reason for the unit not running properly. Be sure to use fresh, clean, and unleaded gasoline. Use fresh fuel (less

Read and follow instructions carefully. 9 Service air cleaner every 25 hours under normal conditions. Clean every few hours under extremely dusty conditions. Poor engine performance and flooding usually indicates that the air cleaner should be serviced. To service the air cleaner, refer to the separate engine manual packed with your unit. The spark plug should be cleaned and the gap reset once a season. Spark plug replacement is recommended at the start of each season; check engine manual for