If the battery is low, the receiver’s channel two relay will latch until reset. In the event of an alarm, the transmitter will activate channel one of the DXR-702, and the receiver’s relay will close for four seconds. IMPORTANT: When the DXR-702 is connected to a security panel it is very important that the central station monitoring the location is advised of which zone(s) will report a carbon monoxide alarm. In a typical installation, the receiver is connected to an alarm control panel. The re

PLAN INSTALLATION INTRODUCTION The AM-KP keypad is designed for use with Linear’s AM/II access control system. The keypad is housed in a rugged cast aluminum enclosure. The die-cast keys have bright, easy-to-read yellow graphics. Each key has a positive tactile “click” feel when pressed. An internal sounder signals when a key is pressed. The keypad can be mounted to a pedestal or directly to a wall. A keylock secures the keypad to the mounting backplate. An incandescent panel lamp lights the

The Arming Mode area will show the Console’s current mode. Pressing the REFRESH button will update the displayed information. Local Connection in Progress Remote Connection in Progress 5.4 SENDING DATA SEND BUTTON PURPOSE: For transferring data from an Account Profile to a DVS-2400 Console. . CAUTION: Receiving the data from the Console will overwrite the data in the Account Profile. If you have made changes to the Account Profile, save the profile, then send the profile to the Console before re

. A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or dealer, and these facts should be communicated to the ultimate users. Copyright © 2008 Linear LLC 218071 B USA & Canada (800) 421-1587 & (800) 392-0123 (760) 438-7000 - Toll Free FAX (800) 468-1340 D-67 DX-12 RELAY LATCH RESET BUTTON (MODEL D-67L ONLY) COMMON NORMALLY OPEN NORMALLY CLOSED ANTENNA RELAY OUTPUT TERMINALS COMMON NORMALLY OPEN NORMALLY CLOSED ANTENNA CONNECTOR SILVER (-) GO

This can dramatically reduce the amount of standby time available from the batteries. To extend the available standby time, the charger board has a “sleep” mode feature which will turn off power to all controls except for any that are wired according to the schematics below. By removing the black jumper cap JP1 located in the upper right hand corner of the charger board this feature can be enabled. After fifteen minutes of inactivity, all controls except those wired as shown below will turn off.

SET TROLLEY 12" FROM PULLEY BRACKET SET TROLLEY LOCATION 12" MAXIMUM DOOR AREA (IN SQUARE FEET) STANDARD SECTIONAL DOORS DOOR SIZE (SQ. FT.) DOOR CONSTRUCTION Insulated Steel Non-insulated Steel Other Construction 250 Fiberglass 210 24 Gauge 22 Gauge Aluminum 180 24 Gauge 20 Gauge Wood 120 20 Gauge 16 Gauge 80 16 Gauge NOTE: On steel insulated doors, a 24 gauge back panel is assumed. 15 Using the Garage Door Operator Opening the Door 1 With the door in view, press the wall station’s UP/ DOWN ARR

. WHEN STATUS REPORTING IS TURNED ON, THE LED SIGNAL INDICATOR WILL BLINK 3 TIMES AFTER ACTIVATION. INSTRUCTIONS FOR THE INSTALLER PROGRAM THE TRANSMITTER INTO THE RECEIVER BY PLACING THE RECEIVER INTO PROGRAM MODE, THEN SEND A SIGNAL TO THE RECEIVER FROM THE TRANSMITTER. REFER TO THE UL LISTED PERS-2400B OR PERS-3600B RECEIVER'S PROGRAMMING INSTRUCTIONS FOR DETAILS. The Model DXS-LRW is a battery powered, miniature, water-resistant*, supervised transmitter designed for use in emergency applicat

2 General Wiring Cautions ................................................................... 2 Intercom Room Station Cautions ...................................................... 2 Important Safety Notes ..................................................................... 3 Component Features ...............................................................................4 Installation ................................................................................................ 5 System De

KEYPAD DETAIL PRESS AND HOLD FOR 2 SECONDS 2. TYPICAL WIRELESS KEYPAD PLACEMENT GREEN OPERATION LIGHT . FIRE BUTTON TO SOUND SIREN AT ANY TIME MODE BUTTONS FOR CHANGING MODES EMERGENCY BUTTON TO SOUND SIREN AT ANY TIME PRESS THE STAR KEY TO RESET THE KEYPAD IF YOU ENTER THE WRONG CODE 3. OPENING KEYPAD KEY TO ACTIVATE HOME AUTOMATION OUTPUT (A) . TABLE-TOP USE KEYPAD FOR ENTERING YOUR USER CODE FROM TOP OF CASE TWIST SCREWDRIVER BETWEEN CASE HALVES UNTIL IT POPS OPEN USE THE FOUR SC

Check the power connections to the receiver. There must be at least 20 VAC at the receiver power connections. ( If a 24V system) . Review the code switch settings. Any mismatch will prevent the receiver from working. Try a different code switch setting. Check the antenna installation. Wait one minute for the receiver to “ warm- up” . Check battery in transmitter. RECEIVER “ CLICKS” WHEN ANY TRANSMITTER BUTTON IS PUSHED, BUT NOTHING ELSE HAPPENS. Check the wire & connections in the STOP circuit.