TO STORE: Unplug can opener and store in its box or in a dry place. Store the cord loosely coiled; never wrap it tightly around the unit. Do not put any stress on cord where it enters the appliance as it may cause the cord to fray and possibly break. IMPORTANT SAFETY INSTRUCTIONS When using electrical appliances, especially when children are present, basic safety precautions should always be followed, including the following: 1. READ ALL INSTRUCTIONS. 2. To protect against electrical hazards, do

The air filter should be cleaned once a month. More frequent cleaning may be necessary depending on outdoor and indoor air quality. Air Filter Removal The air filter on the above models is located behind the Air Inlet Grille. To remove the air filter, grasp the filter handle located on the up side of the Air Inlet Grille and elide the air filter to the up. To reinstall the air filter, reverse the above procedure. ik CAUTION ik DO NOT forget to install the air filter. If the air conditioner

Please read this "Use and Care Manual" carefully before installing and using this appliance. Keep this manual for future reference. Muchase gracias por comprar un aire acondicionado Admirar Lea atentamente el “Manual de Uso y Mantenim ento” antes de instalar y utilizar este producto. Conserve este manual para consultarlo en el futuro. For Service Cali 1 877 465 3566 Para obtener servicio técnico, llame al 1 877 465 3566 TABLE OF CONTENTS Page Air Conditioner Safety.........................

4. Remove solution hoses from fittings in pump. 5. Remove the (2) screws that fasten the pump to the frame. 6. Reverse process to install pump. ONLY QUALIFIED MAINTENANCE PERSONNEL ARE TO PERFORM THE FOLLOWING REPAIRS. BELT REPLACEMENT 1. Turn off all switches and unplug machine. 2. Remove recovery tank and brush. 3. Remove the (2) screws that fasten the solution tank to the frame, and tilt tank back to expose the inside of the frame. 4. Loosen the (4) screws that hold the brush motor in place a

MAINTENANCE ADMIRAL 86038270 05/22/07 16 ! WARNING: ONLY QUALIFIED MAINTENANCE PERSONNEL ARE TO PERFORM THE FOLLOWING REPAIRS. VACUUM MOTOR REPLACEMENT 1. Turn off all switches and unplug machine. 2. Remove recovery tank. 3. Remove the (2) screws that fasten the solution tank to the frame, and tilt tank back to expose the inside of the frame. 4. Locate the vacuum motor wires and disconnect at the connector. Close the solution tank. 5. Remove the (6) screws holding the vacuum motor cover (p/n 860

Used to hold cleaning solution. 6. Recovery Tank Dome. 7. Vacuum Shoe. 8. Brush Housing. 9. Front Lifting Handle. 10. Cleaning Solution Filter. 11. Solution Tank Fill Hose. 4 5 6 7 8 3 2 1 10 9 11 CONTROLS/COMPONENT LOCATIONS 5 ADMIRAL 86038270 05/22/07 1. Solution Intake Cover. 2. Vacuum Intake Cover. 3. Float Shut-Off. 4. Clean-Out Opening. 5. Pour Spout. 6. Lift Handle. 2 1 3 4 5 6 6 FILLING OPERATIONS ADMIRAL 86038270 05/22/07 6 FILLING THE ADMIRAL NOTE: Use clean bucket of water to fill sol

To unplug, grasp the electrical plug, not the electrical cord. Do not handle the electrical plug or machine with wet hands. Do not operate the machine with any openings blocked. Keep openings free of debris that may reduce airflow. This machine is intended for cleaning carpet only. Do not vacuum anything that is burning or smoking, such as cigarettes, matches, or hot ashes. This machine is not suitable for picking up health endangering dust. Turn off all controls before unplugging. Machine can c

This will prevent build-up of alkaline residue in the system. If spray jets become clogged, remove the spray tips, wash them thoroughly, and blow-dry. NOTE: Do not use pins, wire, etc. to clean nozzles as this could destroy spray pattern. Periodically inspect all hoses, electrical cables and connections on your machine. Frayed or cracked hoses should be repaired or replaced to eliminate vacuum or solution pressure loss. If the cable insulation is broken or frayed, repair or replace it immediatel

If care label instructions are not available, use the following information as a guide. Dryer Rack Use the removable drying rack for boots, sneakers, fragile sweaters, nylon stockings – any items that might be damaged by tumbling. To use the rack: 1. Position L-shaped legs against round inset at back of dryer. 2. Rest the two front legs on either side of the lint screen. 3. Check to see that the rack is securely in position. 4. Place items to be dried on top of the rack. Allow space for air to c

To test your power supply cord: 1. Plug power supply cord into a grounded 3-prong outlet. 2. Press RESET. 3. Press TEST (listen for click; Reset button will trip and pop out). 4. Press and release RESET (listen for click; Reset button will latch and remain in).The power supply cord is ready for operation. NOTES: • The Reset button must be pushed in for proper operation. • The power supply cord must be replaced if it fails to trip when the test button is pressed or fails to rest. • Do not use the