for #3 rebar and drilled .218 for ..4-20 self tapping grounding screw and galvanized or painted for protection. 1 - Pole and foundation design based on the following criteria: a) Uniform building code exposure B or C and 1.5 stability factor. b) Vertical soil pressure of 2000 pounds per square foot. BubbleLevelGround PoleMust BeVertical InAll DirectionsWithin .19 InchesAt Top (0.3.) c) Lateral soil pressure of 400 pounds per square foot. d) Concrete compressive strength of 2500 pounds per square

The mount can be positioned manually or by using a crane; however, Andrew recommends that this procedure be performed using a crane to ensure speed and ease of installation. Figure 3-2: Crate Unpacking As stated previously, the pedestal ground mount installation process can be conducted manually or by using a crane. The following steps provide the necessary procedures for installing the ground mount assembly using a crane. 16 Installation Procedures Step 1 Step 2 Step 3 Step 4 Carefully remove t

Any accumulated imbedded dirt, corrosion, grease, or oil deposits that require further cleaning may be removed with a bristle or wire brush and a cleaning solvent such as trichlorethylene or equal. After cleaning, allow cleaned parts to dry for 10 to 15 minutes before placing the equipment into operation. The frequency of inspection is contingent upon the user’s individual standards and the operational environment in which the earth station is located. However, a visual inspection of the earth s

Slippage can cause the corresponding assembly to move, causing antenna misalignment. When designated, the A-325 hardware should be tightened according to the following tensioning procedure. NOTE: Tensioned bolts are for final connections only and should not be loosened for reuse. Lubricate the bolt threads with the provided stick wax to reduce friction. Insert the bolt, and add a flat washer—if required. Do not allow wax under the flat washer. Add the nut, and finger tighten. After the connectio

60462 Internet: Other Europe: +44 1592 782612 Copyright © 2005 by Andrew Corporation Table of Contents Introduction How to Use This Manual Getting Started Installation Procedures Operation Preventive Maintenance Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Proprietary Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

• Use 7/8 by 2-1/4 in (57 mm) hardware Note: Angles are attached edge out with flat of angle facing inward. 301786 Figure 16 Align panning frame/azimuth pivot assembly by swinging panning frame through its entire arc. Slightly snug panning frame/pivot assembly hardware, and again swing panning frame through its entire arc. Continue this procedure until mounting hardware is ready for tensioning. Note: Do not tighten hardware on 301786/201022 azimuth pivot assemblies at this time. 21 Installation

A World of Solutions. International Telephone: +1-708-873-2307 Fax: +1- 708-349-5444 Internet: DO NOT DISCARD CONTENTS The product in this packaging was placed in the market after August 13, 2005. Its components must not be discarded with normal municipal or household waste. Contact your local waste disposal agency for recovery, recycling, or disposal instructions. HARDWARE SORTER HARDWARE SORTER DATE DESCRIPTION REV. 1/06 ECN9007200 Rev A 8/06 ECN9007484 Rev B VSAT ANTENNA/MOUNT/LNB LIMITED TWE

Andrew installation instructions are written for such installation personnel. Antenna systems should be inspected once a year by qualified personnel to verify proper installation, maintenance, and condition of equipment. Andrew disclaims any liability or responsibility for the results of improper or unsafe installation practices. Do not install near power lines. Power lines, telephone lines, and guy wires look the same. Assume any wire or line can Do not install on a wet or windy day or when

When the dipole element pairs are spaced at 90° to each other, an omni-directional or circular pattern results. When both sets of dipoles are in line (collinear - see the DB404L illustration in Figure 1), the antenna has a directional characteristic, giving an elliptical pattern as shown in Figure 2. Also, see Figure 3 for gain variation with frequency for DB404 and DB404L antennas. The change from one radiation pattern to the other is easily accomplished. The banding clamps that hold the dipole

60462 Internet: Other Europe: +44 1592 782612 Copyright © 2005 by Andrew Corporation Table of Contents Introduction How to Use This Manual Getting Started Installation Procedures Operation Preventive Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Proprietary Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .