The glass is hinged to allow a more thorough cleaning (BX-4 only). Figure 3-1. Removing the inner door glass (BX-4 only). 6. Clean the glass with a suitable glass cleaner. 7. Wipe down the oven and clean the racking with a damp cloth. 8. Reassemble all parts back in the oven after cleaning. WARNING In the 4-tray oven, do not damage the control probe protruding from the upper corner of the inside rear wall of the oven chamber. Belshaw Bros., Inc. .. 1750 22nd Ave. S. .. Seattle, WA 98144 .. Phone

.” BSP female thread on the oven. . 3 foot-long hose with .” B.S.P. female fittings at both ends (included) . Inline backflow valve (customer must provide and fit) . 15-60 p.s.i. water pressure Installation The BX oven should be connected to a local means of isolation. . To stop the oven in an emergency, switch off at the wall isolator. Initial Cleaning Carefully wipe the interior of the oven and all accessories with a clean cloth soaked in warm soapy water and allow the oven to dry completely.

Then slide the .” pin through the upper bearing hole on the wall plate, through the bushing and then through the lower bearing hole on the wall plate. Place washer provided on the upright pin to serve as a thrust bearing. Oil pin lightly with light machine oil. 6. Set the small straight arm in place on the pin of the first bracket arm. This should be also mounted so that the pin is pointing up. Place .” washer provided on the pin. Oil pin lightly with light machine oil. 7. The donut cutter shoul

Cake Donuts Yeast-Raised Donuts .. F .. C .. F .. C Room temperature 72 22.2 72 22.2 Dry mix temperature +70 +21.1 +70 +21.1 Total A 142 43.3 142 43.3 Desired batter temperature 75 23.9 80 26.7 x3 x3 x3 x3 Total B 225 71.7 240 80.1 Total B 225 71.7 240 80.1 -Total A -142 -43.3 -142 -43.3 Desired water temp. for cake donuts 83.. F 28.4.. C 98 36.8 .. .. Figure from above 98 36.8 Temperature increase during mixing (average: 30.. F/17.. C) -30 -17 Desired water temperature for yeast-raised donuts 6

.. 1750 22nd Ave. S. .. Seattle, WA 98144 .. Phone 206-322-5474 .. Fax 206-322 MN-1126EN 618L, 624, and 634 Electric Fryers 13. Install the drain tray mount brackets (removed in step 4) on the opposite side of the fryer. 14. Put the drain tray in place, so its holes line up with the holes in the mount brackets. 15. Slide the drain tray hinge shaft through the holes in the mount brackets and the drain tray. 16. Tighten the acorn nuts (removed in step 1) on the ends of the drain tray hinge shaft.

Fax 206-322-5425 MN-1126EN 618L, 624, and 634 Fryers Belshaw Bros., Inc. .. 1750 22nd Ave. S. .. Seattle, WA 98144 .. Phone 206-322-5474 .. Fax 206-322 618L, 624, and 634 Electric Fryers MN-1126EN FIGURE C-2. 618L HEATER HEAD ASSEMBLY. BILL OF MATERIAL FASTENERS ITEM QTY. PART NO. DESCRIPTION ITEM QTY. DESCRIPTION 1 1 618L-527 Heater Head Case Assembly A 9 10-24 x 3/8 Round-Head Slotted Machine Screw 2 1 MK-89 Pilot Light–250 Volt, Red B 1 #4 x 3/16 Blunt-Nose Sheet Metal Screw 3 1 MK-64 Pilot L

10. Continue supplying shortening to the kettle as required. Keep the kettle filled up to the “Oil Level” marks on the side. 11. When you are done frying donuts, move the on/off switch to the OFF position. Belshaw Bros., Inc. .. 1750 22nd Ave. S. .. Seattle, WA 98144 .. Phone 206-322-5474 .. Fax 206-322 618L, 624, and 634 Electric Fryers MN-1126EN Cleaning 3 For your safety, observe the following warnings throughout the entire cleaning process. WARNING Thoroughly clean and dry the floor if short

Level the fryer. Follow these steps: a. Check to see if the fryer is level. To do so, place a level across the top of the fryer cabinet. b. If the fryer is not level, lift the fryer using a fork lift or pallet jack, and turn the legs to adjust them. c. Using the fork lift or pallet jack, lower the fryer to the floor. Be sure that all the legs rest on the floor when the fryer is level. 5. Bolt the fryer to the floor. The foot of each leg has two holes in it for this purpose. WARNING To avoid seri

• 1750 22nd Ave. S. • Seattle, WA 98144 • Phone 206-322-5474 • Fax 206-322-5425 C-4 MN-1141EN 718LCG, 724CG, and 734CG Gas Fryers 734CG PARTS LIST. ITEM QTY NUMBER PER NUMBER PER UM DESCRIPTION-TRUNC. 724G-0239 8 EA AIR SHUTTER POWER CORD, 18GA INSTRUCTION LABEL 232 1 EA SJO 724G-0242 1 EA CG #PLT-0001 1 EA CLEAR NEON PILOT LIG IGNITER-CONTROLLER #PLT-0002 1 EA CLEAR NEON PILOT LIG 724G-0269N 1 EA NG DRAIN VALVE 724G-0273 1 EA GAS VALVE-NG 618L-0098 1 EA KNOB,EXT 724G-0299 1 EA DOOR MGT BRACKET

c. Watch the ignition sequence at the burner. If the spark still does not stop after the pilot lights, replace the ignition module. If the main burner does not light, check for 24V AC across MV-MV/PV terminals. If there is no voltage, replace the module. Also, check the electrical connections between the module and the gas control. If they are okay, replace the gas control or the gas control operator. Appearance Cause small blue flame lack of gas due to clogged orifice filter lack of gas due to