-36 Figure 45. Crosscutting blade. Combination Blade: Used for cutting with and across the grain. A compromise between a rip blade and a cross-cut blade, a 10" combination blade will typically have between 40-50 teeth (Figure 46), an alternate top bevel and flat or alternate top bevel (Figure 49) and raker tooth profile. The teeth are arranged in groups of five. The gullets are small and shallow within the groups of five teeth, similar to a cross-cut blade; then large and deep between the groups

This pressure is controlled by the regulator and is always less than or equal to the tank pressure. Tank Pressure Gauge:The tank pressure gauge indicates the reserve air pressure in the tank. Regulator:Controls the air pressure shown on the outlet pressure gauge. Pull the knob out and turn clockwise to increase pressure and counterclockwise to decrease pressure. When the desired pressure is reached push knob in to lock in place. Drain Valve:The drain valve is located at the base of the air tank

10. For more assistance, or to install a complete o-ring set, refer to the breakdown diagram in the back of this manual for component locations. t20568 11.4" brad nailer -11 cleaning & lubrication cleaning use a good solvent to clean the nose assembly of the nailer. always be sure that the nailer is dry before using it again. do not allow dust, chips, sand, etc. into the air connectors or into the body of the nailer; this may result in leaks and damage to the nailer and the air couplings. never

Serious personal injury may occur. The Models G1004/08 feature an R-8 spindle which accepts many industrial collets and arbors. To install a collet or an arbor: 1. Release the latches on the head lid and open it. 2. Determine the location of the pin inside the spindle. 3. Align the keyway of the collet to the side where you found the pin and insert the col- let or cutting tool’s arbor up into the spindle housing. Rotate the collet slightly to line up the keyway with the pin in the spindle bore.

The C1553/C1554 (also sold as C1552) combination produces the classic Ogee finish. Fitted with precision guide bearings, these bits are capable These router bits have sharp edges. use care while removing the waxy protec- tive coating. Never turn on the router with the protective coating still on the bit. •Failure to follow theSE guidelines will result in seri- ous personal injury. •ALWAYS WEAR ANSI APPROVED EYE AND EAR PROTECTION WHEN USING THIS BIT. •The use of a router table is strongly recomm

A hold- down device such as a featherboard should be used to keep the workpiece secured against the fence. Make a test cut to ensure that the complete profile is being cut. Adjust, if necessary, and re-test. Run all of the stiles and rails for the project through the cutter before changing bits to do the rail ends. 529003622 © May 2003 Grizzly Industrial, Inc. Step 2: Cutting Rail Ends Unplug the router and change bits. Raise the router bit so the top of the bead is Outer Side 1.16" below the to

Step 1: Cutting Stile and Rail Edges Make sure the router is disconnected from the Top of Bead • Unplug router before power source. Install the stile and rail cutter. Outer Side installing or adjusting (C1551 or C1554.) Attach the router to your router table and adjust the height of the bit until the top of the bead is 1.16" below the top bit. • Keep all guards and anti- of your stile. See Figure A. Adjust the fence kickback devices in place. until it is flush with the bearing. (The bearing • Do

#JM10748 printed in ChinA ..........................................................................................................................................................................................................................................................................................................................................................................................................................................................................................

.. .. .. .. .. .. .. .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .. .. .... .... .... Column Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION P0643001 KNURLED KNOB PSS01M SET SCREW M6-1 X 10 P0643003 DEPTH CONTROL PSB02M CAP SCREW M6-1 X 20 P0643005 WING SCREW M6-1 X 35 PSB11M CAP SCREW M8-1 X 16 PW01M FLAT WASHER 8MM PSB14M CAP SCREW M8-1.25 X 20 P0643009 DEPTH CONTROL MOUNT P0643010 LIFTING EYE BOLT P0643011 COLUMN PSB33

#TS9041 PRINTED IN CHINA ...........................................................................................................................................................................................................................................................................................................................................................................................................................................................................................