3 Maintenance Care and Storage .................................................................. 3 Contents ................................................................................................................. 3 Getting to Know Your MiniCam™ Pro.........................................................4 Installation............................................................................................................. 4 WebCam Companion 3 ........................................

Locate the segments around the outer edge of the timer’s dial. These segments, each representing 15 minutes, can be pushed out and away from the edge of the dial (try using the tip of a pen or pencil). Conversely, segments that have been pushed out can be easily pushed back in by hand. Be sure all segments are pushed in before programming. Select a time period (or periods) you want the appliance turned on, then push out ALL the segments that fall on or within that time period. For example, to ha

Notice ALL segments between 10 PM and 2 AM have been pushed out. Current time is 8:00 PM. CurrentTimeCurrentTimeCurrentTime24 Hour Outdoor Timer Instructions: 1. Locate the segments around the outer edge of the timer’s dial. These segments, each representing 15 minutes, can be pushed out and away from the edge of the dial (try using the tip of a pen or pencil). Conversely, segments that have been pushed out can be easily pushed back in by hand. Be sure all segments are pushed in before programmi

• Do not exceed capacity. • Do not use timer with devices that could have dangerous consequences due to inaccurate timing, such as sun lamps, heaters, etc. • Plug directly into receptacle. NOTICE • No user serviceable parts. Install setup: 1. Plug timer into wall outlet for a 5 minutes to charge internal battery. NOTE: You can unplug the timer to set after initial battery charge. 2. Before programming all settings should be reset. Use a toothpick or pencil to push the “R” button. 3. Select AM/PM

2. Press the HOUR, MINUTE and WEEK buttons as necessary to revise the displayed ON or OFF time and day(s). To remove or restore a setting: 1. Press the PROGRAM button (hold down to scroll) until the display shows the setting you want to remove or restore. 2. Press the RST/RCL button. - If removing, the display will replace the setting with dashes. Pressing the RST/RCL button again will restore the previous setting. To Operate the timer: 1. After setting the timer, plug it in and connect the devi

Setting The House Security Code Setting The House Security Code is pre-set at the factory and no further adjustment is normally required. However, if you experience erratic or no operation from your chime you may want to reset the House Security Code Setting. Each component has jumpers for setting the house security code: The chime and pushbutton must be set to the same house security code for the combination to operate together. Note: The push button has 3 additional jumpers that are used to se

1. Remove the battery cover on the chime. 2. Unplug the red and white wires inside the battery compartment. 3. Remove the battery pack and discard appropriately. Required Tools: Small flat blade screwdriver, drill, drill bit, and phillips screwdriver. Included Hardware: (2) Plastic screw anchors (2) 4x20mm screws (for anchors) (2) 3x20mm screws (2) Double sided adhesive pads The wireless door chime Kit has two components: Chime (receiver) Push-Button (Transmitter). Chime Tune Setting All wireles

Locate the two door chime wires emanating from the existing door chime circuit. Test the door chime by touching the two wires together, completing the circuit. If door chime does not sound,check transformer or chime. Turn off power. Attach one wire to each of the screw terminals on the back of the button. Mount button in desired location with two screws provided. Install according to applicable local electrical codes. -EEL Wall

3. Locate the House Security Code door and screw located on the back of the chime (See the chime components picture above). Remove the screw and take off the door. 4. Locate the chime and pushbutton jumpers shown below. House Code Jumpers Chime and Pushbutton Jumpers 5. To change the house code, add or remove jumpers as needed. It is recommended to change only one jumper at a time and then test the system for proper operation. The jumpers on the chime and pushbutton must match exactly. Push Butt

INTRODUCTION The antennas used for digital terrestrial broadcasting can be easier and smaller. This indoor antenna (24702) is special designed for digital terrestrial broadcasting reception. The benefits of use this antenna are easy to install, light weight, compact size…etc. With state of the art low noise amplifier technology and circuitry, it will provide the best reception. And the compact and stylish housing design can be accompanied with your digital STB and TV. This digital indoor antenna