• Shake gas container a few times to warm fuel up. • Make sure the Fuel Adjustment Knob is in the “OFF” position (fully clockwise). • Insert the Butane container nozzle tip vertically down into the unit gas valve refill opening. Use a pumping action for best results (Figure 1). • After filling, allow a few minutes for the gas to stabilize. GAS 1 IGNITION •Turn the Fuel Adjustment Knob counter-clockwise 1 full turn. (Figure 2) • To Ignite: Push Safety Slide Bar up and hold while depressing Igniti

10. At the end of each work session put the paint chips and debris in a double plastic bag, close it with tape or twist ties and dispose of properly. 11. Remove protective clothing and work shoes in the work area to avoid carrying dust into the rest of 3 Important Safety Instructions (cont’d) the dwelling. Wash work clothes separately. Wipe shoes off with a wet rag that is then washed with the work clothes. Wash hair and body thoroughly with soap and water. 12. WARNING: To reduce the risk of fir

Slower speed is compensated by the wider softened areas. Heat will also penetrate deeper. 2) As paint begins to blister and bubble, move gun slowly in a steady progression across the surface. Follow closely with a scraping knife (a 2-inch-wall scraper works best) to scrape the loosened paint. Preheat scraper as you are heating the paint surface. This increases the speed of paint stripping. a. Removal of paint by using heat is based on the fact that all organic paints soften at elevated temperatu

Only empty fuel tank in a well ventilated area and away from ignition sources. Remember butane is heavier than air. 2. Depress the filler valve at the back of the tank with a small bladed screwdriver and let the butane gas escape through the small orifice opening. It takes approximately one minute for the butane to escape from the tank. Be careful that the butane does not hit against your fingers or hands. This could cause frostbite of the skin. 3.One method is to poke a small bladed screwdriver

in correct position as illustrated (fig 1). Replace cover. 2 COVER TIP UNIT BASE RECEPTACLE 1 SLIDE HOW TO MOUNT THE TIP (2) • Align tip base over unit receptacle. Push inward until tip is fully seated on base. •To remove ensure tip has cooled. Insert tip remover plate supplied with unit at base of tip and push tip away from base. OPERATING INSTRUCTIONS • Move slide switch forward to ON position. (Push button will not operate in OFF position of slide switch for your safety.) • Push button, pilot

Merci de lire ce manuel, s’assurer de l’avoir compris et le conserver en reference. Por favor lea, entienda y guarde este manual para referencia futura. Regulatory Information Declaration of Conformity: (According to EN 45014) Manufacturer’s Name: Master Appliance Corp. Manufacturer’s Address: 2420 - 18th Street Racine, WI 53403 U.S.A. Declares that the following product: Product Name: UT-100, UT-200 Conforms to the following product specifications: SAFETY DIRECTIVES: EN 123 12.81, EN 292 Parts

Become familiar with all controls for safety. Lisez ce manuel entierement avant de commencer a utiliser l'outil. Familiarisez-vous avec tous les controles de securite. Lea completamente este manual antes de tratar de usar esta herramienta. Para mayor seguridad, familiaricesecon todos los controles. Exhaust opening Orifice d'echappement Salida de escape Gas open lever Levier d'admission de gaz Palanca de abertura de gas Gas control lever Levier de controle de gaz Palanca de control de gas Made in

Fabrique aux Etats-Unis Hecho en EE.UU. Please read, understand and keep this manual for future reference Lire et bien comprendre les instructions contenues dans ce manuel et les conserver comme reference. Por favor lea, comprenda y guarde este manual para futura referencia. Description & Introduction The Masterflow® Heat Blower is a heavy-duty, industrial- quality heat blower suitable for continuous duty applications. It produces a high volume of hot air for demanding industrial applications. T

Fabrique aux Etats-Unis Hecho en EE.UU. Please read, understand and keep this manual for future reference Lire et bien comprendre les instructions contenues dans ce manuel et les conserver comme reference. Por favor lea, comprenda y guarde este manual para futura referencia. Description & Introduction The Master Heat Gun is a heavy-duty, Industrial-quality, general-purpose heat gun. High temperature Industrial jobs are done faster with this heat gun, because our MASTER models have higher power a

Consult factory if problem exists. Read and follow instructions before using. Keep away from children. After filling: fuel cell contains gas under pressure. Do not use near open flames, heaters or combustibles. Store properly when not in use. Always make sure Microtorch is cool before removing fuel cell. Remove fuel cell before storage. Do no store fuel cell above 104°F/40°C. CAUTION: Flame appears invisible in sunlight and could cause severe injury if not used with extreme caution. WARNING: Thi