WARNING: If the information in these instructions is not followed exactly, a fire or explosion may result, causing property damage, personal injury, or death. - Do not store or use gasoline or other flammablevapors and liquids in the vicinity of this or any other appliance. - WHAT TO DO IF YOU SMELL GAS: • Do not try to light any appliance. • Do not touch any electrical switch; do not use anyphone in your building. • Immediately call your gas supplier from aneighbor’s phone. Follow the gas suppl

7. Turn HI-LO burner control knob to desired setting and close control door. PILOTOUTVENTLOTHTPTHTPHIININ 5. Allow sufficient length of time (minimum 5 minutes) for any gas in the combustion chamber to escape. If you still smell gas, STOP! Follow “B” in the safety information above on this page. If you do not smell gas, go to the next step. 8. Set thermostat to desired setting if applicable. 9. If the appliance will not operate, follow the instructions "To Turn Off Gas To Appliance" and call you

Any attempt to use a different log set in the fireplace will void the warranty and will result in incomplete combustion, soot ing, and poor flame quality. REFERENCE Firebox Accessories / Parts Cat. No. Model No. Description 88L5 FGE Bag of Glowing Embers (1 oz. rockwool) 80L4 FDVS Bag of Decorative Volcanic Stone Table 8 Glowing Embers Bag of Glowing Embers (rockwool) Separate into Quarter Size (separate) Pieces WARNING DONOTattempttoinstallthelogs until the appliance installation hasbeencomplet

INSTRUCTIONS D’ALLUMAGE — ELECTRONIC INSTRUCTIONS D’ALLUMAGE POUR VOTRE SECURITE, LISEZ CES INSTRUCTIONS AVANT L’ALLUMAGE A. Lorsque vous allumez l’appareil, suivez exactement ces instruc- tions. B. AVANT L’ALLUMAGE: Assurez-vous que vous ne detectez aucune odeur de gaz autour de l’apareil ainsi que pres du sol; certains gaz, etant plus lourds que l’air, descendent au niveau du sol. VOICI CE QUE VOUS DEVEZ FAIRE SI VOUS DECELEZ UNE ODEUR DE GAZ • Eteignez toute flamme visible. • Ouvrez les fenet

Reassemble the remaining components by reversing the procedures outlined in the preceding steps. Step 12. Attach the conversion label (provided in the conversion kit) next to the rating plate on the appliance. Step 13. Turn on gas supply and test for gas leaks (refer to Page 16). Always test pressures with the valve regulator control at the highest setting . All Models Note the following: Use pipe joint compound or Teflon tape on all pipe fittings before installing. Ensure propane-resistant comp

Distribute the pieces over the surface of the burner, as shown in Figures 9 and 10. Do not use more than is necessary. Position the embers on the small holes of the ember bed area. Note: Make sure the glowing ember material does NOT cover the main burner slots. 5. Install the Logs. The logs have locating notches or slots to help ensurethattheyareproperly positioned. The top logs that rest on lower logs, do so over notches, indents or nubs. Proper log placement is critical to prevent sooting. Log

Interrupteur ON/OFF FFONIISPNOLORTNOCRETINGIVue de face MAINTENANCE SCHEDULE Annually (Before the onset of the Burning Season) MAINTENANCE TASK ACCOMPLISHING PERSON PROCEDURE Inspecting/Cleaning Burner, Logs and Controls Qualified Service Technician Inspect valve and ensure it is properly operating. Check piping for leaks. Vacuum the control compartment, fireplace logs and burner area. Check Flame Patterns and Flame Height Qualifi ed Service Technician Refer to Figure 10 on Page 11 and verify th

Install the nailing flanges - 8 (CDST), 4 (CDPF, CDCL and CDCR) - as shown in Figure 7 using the existing screws. Position the fireplace within the framing. When required, the flanges may be bent 90 degrees by hand or with the assistance of a hammer. Use wood screws to secure the nailing flanges to the framing. See Table 2 on page 4 for clearances of framing members to cabinet parts in the nailing flange area. The nailing flange itself is exempt from these clearances. Floor Nailing Tabs Secure t

56 ... 97 ... 103 104 ... 106 ... 1 1 1 1 0 0 0 0 1 0 1 2 1 2 0 1 2 2 0 2 0 0 2 0 58 ... 61 ... 64 ... 67 109 ... 116 121 ... 124 ... 1 1 1 1 0 1 1 1 0 1 0 2 1 0 1 0 0 3 3 3 2 0 0 0 68 ... 70 73 74 ... 128 130 135 ... 138 ... 1 1 1 1 1 1 1 1 0 1 0 0 0 1 2 0 1 3 3 0 2 0 0 3 79 80 82 82 ... 145 ... 147 ... 150 ... 152 1 1 1 1 1 1 1 1 1 1 0 0 0 0 1 1 4 0 4 0 0 3 0 3 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 13 Stabilizer A1 20' Max. B1 10' Max. Offset Elbow Figure 37 A1 C1 B1 B2 C2 A2 A1 C1 B1 B

Wait For Internal Check Delay. YES • Igniter Warms Up And Glows Red. NO • Replace Igniter/Flame Rod Assembly. YES YES1 • Check For Proper Voltage At Control Harness (See Insert A). Voltage Should Be 24V Between Thermostat Or Pressure Switch And 24V Common And 24V Hot. 2 • With Pilot Burner Cable Connected, Measure NO Voltage At Valve HSI Element Output. 24V Nominal. (See Insert B) 1 2 YES • Replace Valve. Insert A End View Of Control Harness Connector 24 Volt Hot 24 Volt Common 24 Volt Switched