4-5b Pre-Wired source and sensor wiring methods. 6 5 4 3 2 1 or 6 5 4 3 2 1 Source Sensor Red Green Power Head Dashed Line = striped wire Solid Line = white wire Wall Wall Ceiling 1/2" 2" Cover clips FIG. 4-9 Install rear cover. Insulated Staple Wire Nut CONNECTING TO POWER 5 Plug the operator into a properly grounded electrical outlet. (Fig. 5-1) • To reduce the risk of electrical shock, this equipment has a grounded type plug that includes a third (grounding) pin. This plug will only fit a gro

2-3). NOTE: For header bracket and bolts locate Bag 2from Box 1. NOTE: The bolts supplied in Bag 2 are designedto be used on pressure treated lumber. 2. Mounting the header bracket. • Hold header bracket against wall (Fig. 2-3). • Position bracket as shown. – Place center on vertical line. – Bottom edge on final height line. • Mark screw hole locations on wall. • Drill 3/16" pilot holes at each screw hole mark. – Fasten header bracket with 2 lag screws (provided) (Fig. 2-3). Header bracket must

WARNING PN# 3642036534, 02/26/2010 REV. 1 1 2 3 41 2 31 2 WHITE BLANC BLANCO BLACK NOIR NEGRO GREEN VERT VERDE TRANSFORMER TRANSFORMATEUR TRANSFORMADOR PRIMARY PRIMAIRE PRIMARIO BLACK NOIR NEGRO BLACK NOIR NEGRO YELLOW JAUNE AMARILLO WHITE BLANC BLANCO BLACK NOIR NEGRO RED ROUGE ROJO BLACK NOIR NEGRO HALL SENSOR CAPTEUR DE PASSAGE SENSOR DE PASILLO YELLOW JAUNE AMARILLO MOTOR MOTEUR MOTOR GREEN VERT VERDE RED ROUGE ROJO RED ROUGE ROJO GREEN VERT VERDE WHITE BLANC BLANCO BLUE BLEU AZUL ORANGE ORA

106730 Rev A1 April 2006 April 2006 Technical Publications Genie Industries has endeavored to deliver the highest degree of accuracy possible. However, continuous improvement of our products is a Genie policy. Therefore, product specifications are subject to change without notice. Readers are encouraged to notify Genie of errors and send in suggestions for improvement. All communications will be carefully considered for future printings of this and all other manuals. Contact Us: e-mail: te

B Install Lens into slots in Motor Cover. • Insert Bottom hinges into slots provided in metal front cover of Power Head. • Flip Lens up and fasten with molded latches on lens. Ins tallation of Lens and Bulb Figure 14 Install Lens and Light bulb Transmitter Compliance Statement WARNING TO REDUCE THE RISK OF SEVERE INJURY OR DEATH 1 READ AND FOLLOW ALL INSTRUCTIONS. 2 Never let children operate or play with the Door Controls. Keep the Remote Control away from children. 3 Always keep the moving doo

For use only with sectional doors. Homelink® and Car2U® compatible For Answers and Assistance: 1.800.354.3643 or visit SAVE THIS MANUAL FOR FUTURE REFERENCE Installer: Leave this manual with homeowner. PN# 37026500123, 2/26/2010 REV.1 Homelink® is a registered trademark of Johnson Controls Technology Company. Car2U® is a registered trademark of Lear Corporation. © The Genie Company 2010. X900-786 Models 2022/2024/2042GARAGE DOOR OPENERS ALWAY S AT YOUR COMMAND Includes: 2-Bulb Light System Wall

If you have not, remove all ropes and/or cables and disable garage door lock NOW before continuing with installation (Fig. 1-8). CAUTION Use 5/16"-18 x 1/2" Bolts FIG. 1-5 Rail - Power head assembly. FIG. 1-6 Chain adjustment. Chain Pulley Bracket (at wall end of rail) Chain T-Rail at center of rail assembly 1/8" T-Rail Chain Tighten nut to move pulley this direction Use 1/2" socket on adjustment nut Set assembled power head and rail aside. Begin with Section 2 INSTALLATION. Assembly for BELT DR

2. You can quickly press and release the "Close Travel Limit" button to move the door in small increments. You can also use the "Open Travel Limit" button to move the door slightly in the UP direction. 3. Door is fully closed when the bottom edge of door presses firmly onto the ground. 4. Once the door is in the desired position, press and hold the "Close SET Limit" button for 5 seconds. The LED indicator light will blink green once. This stores the closed position in memory. C) OPEN TRAVEL LIMI

2" Carriage Bolt /4"-20 Hex Fmange Nut RAIL SECTION CONNECTION WOODEN DOORS DOOR ARMS SlideCollarover long Nook TO (SHORT AS POSSIBLE) >, c c_ E Mate Hooks LJo _J GJ _c F= < ARMS L0 SHde Collar over Joint J c _6 (LONG AS POSSIBLE] I Snap CHp behind Collar L_ _O O O @ CONNECT RAK TO POWER HEAD ATTACH RAK STRAP TO [ND RAK SECTION CONECTEEL_ARANDALACAJADELMOTOR [NSTALEELENSA_BLEDELCORRED_ZO MA_N_TICOA LASBARANDAS Attach Rail Strap to End Rail Section, A o Threaded stud of Rail strap should pass in

3 Remove all ropes, and disable all locks connected to the door before installing operator. 4 Install door operator 7 feet or more above the floor. Mount the emergency release knob 6 feet above the floor. 5 Do Not connect the operator to the source of power until instructed to do so. 6 Locate the control button: • Within sight of door. • At a minimum height of 5 feet, so small children cannot reach it. • Away from all moving parts of the door. 7 Install the entrapment WARNING label next to the w