of LEDs: Estimated battery life: Size: Weight (with battery): 300mS per LED 1 kHz -30 dB to + 7 dB balanced 100 Ohms unbalanced 200 Ohms balanced 17 6 hours of operation 4.65” W x 6.95” H x 2.275” D (11.8 x 17.65 x 5.78 cm) 2.8 lbs. TYPICAL CABLE SCAN CHART CABLE JACKS LEDS SEND RECEIVE Speaker 1/4” Banana Speaker 1/4” Speak-on® 1 Instrument 1/4’ 1/4’ Microphone XLRf XLRm Stereo Sound Card 1/8” 1/8” MIDI (5 pin) MIDI MIDI Telephone RJ11 RJ11 Note: This will vary greatly depending on the number o

Side Chain circuits are often used in "ducking". Ducking is momentarily lowering one signal under another signal. For example, you may wish to automatically lower a music signal under a paging microphone signal, then have the music return to normal level after the page is over. This would be accomplished by running the music into the compressor, and having the page signal connect into the Side Chain return. The page signal must also be connected to the main mixer or amplifi er as well. When the

Tube compliment Four stages of gain using low noise 12AX7A’s Phantom power +12 vdc 50 ma on the MIDI jack pin 3, 1=gnd Dimensions 19" X 1.75" X 10" (48 X 4.5 X 25 cm.) Weight 7 lbs. (3.2 kg) Accessories (optional) MP80 controller, or dual pedal controller OWNERS MANUAL INTRODUCTION The MP45 is the culmination of a great deal of effort and has performance and convenience features that make it absolutely unique. * Programmable Knobs * Programmable EQ sliders with popular center freqs. * True non-v

Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. IN NO EVENT SHALL WE BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESSED OR IMPLIED, WHATSOEVER. Some states do not allow the exclusion or limitation of special, incidental or consequential damages so the above limitation or exclusionmay not apply to you. This warranty gives you specific legal rights, and you may

Products returned to us or to an authorized Service Center must be accompanied by a copy of the purchase receipt. In the absence of such purchase receipt, the warranty period shall be one (1) year from the date of manufacture. This warranty shall be invalid if the product is damaged as a result of defacement, misuse, abuse, neglect, accident, destruction or alteration of the serial number, improper electrical voltages or currents, repair, alteration or maintenance by any person or party other t

4 Q 70 Watts RMS/ch. 8 Q Bridged - 200 Watts RMS or 70 Volt 8 Q Input Connectors: 1/4" TRS balanced and RCA Output Connectors: 5-way binding posts Sensitivity: <1 VRMS for full output THD: <.08% (1 kHz @ 1 Watt) S/N Ratio: 106 dBU Power Bandwidth: 50 Hz - 25 kHz, +/-1 dB Damping Factor: > 150 Slew Rate: 100 Volts/microSecond Phase Shift: <10 Deg.,20Hz- 20kHz Input Impedance: 10 KQ Balanced Power: 120 VAC 60Hz 2.5A 230 VAC 50 Hz Size: 19” x 3.5” x 7.5” (48 x 9 x 19 cm) Weight

1/4" RCA, R & L balanced XLR 6: 1/4" TRS Direct Input jacks Outputs: 12: 1/4" TRS Stereo jacks 6: 1/8" (3.5 mm) TRS Stereo jacks Max Gain: 20 dB/Channel Output Power: 972 mW/side, 1944 mW/Channel ( @ 32 Ohms ) Frequency Response: DC - 30 kHz S/N Ratio: 90 dB THD: <.008% IMD: <.008% Phase Shift (In to Out): 0 deg. Slew Rate: 25 V per microsecond Second Crosstalk: - 65 dB Power 12 VAC (Rolls Model PS12) Weight: 7 lbs (3KG) Size: 19” x 1.75” x 6.5” (48cm x 4.5cm x 17cm) INTRODUC TION T hank y ou f

The obligation of Rolls Corporation under this warranty shall be limited to repair or replacement (at our option), during the warranty period of any part which proves defective in material or workmanship under normal installation, use and service, provided the product is returned to Rolls Corporation, TRANSPORTATION CHARGES PREPAID. Products returned to us or to an authorized Service Center must be accompanied by a copy of the purchase receipt. In the absence of such purchase receipt, the warran

They may be used together if desired. To configure a channel’s 1/4” jack as a Direct Out, first remove the RM82 lid. For each channel there are dual three-pin headers with shorting jumper on two pins. The setting from the factory is on “IN”. By moving the shorting jumpers to the configuration shown as “OUT” (one jumper up, the other down), the jack then becomes a Direct Output. CONFIGURING THE 1/4” INPUT JACKS AS INSERTS To configure a channel’s 1/4” jack as an Insert, first remove the RM82 lid