1 Chapter 1 - Getting Started ................. 3 Controller Hardware Overview........................ 4 Control Module Overview............................ 6 Chapter 2 - Controller Setup................. 9 Adjust Display Contrast.............................. 9 Set Controller Date and Time.........................10 Select Time Zone..................................11 Select Auto Daylight Savings Option....................11 Set Maximum Active Station Count.....................12 Sele

MODEL 22610709 - 12 FOR A TORO Z-MASTER UNIT 2001 P# Q0233 REVISED 01/08/01 PECO PECOPECOPECOPECOPECO OWNERS OWNERSOWNERSOWNERSOWNERSOWNERS MANUAL MANUALMANUALMANUALMANUALMANUAL Save This Manual For Future Reference MODEL 22610709 - 12 TORO Z-MASTER 2001 PECO PECOPECOPECOPECOPECOPeCo Limited Warranty for New Products A. WHAT IS WARRANTED? PeCo extends the following warranties to the original purchaser of each new PeCo consumer product subject to the following limitations. 1. PRODUCT WARRANTY. An

WARNING! NEVER operate the mower unless the discharge guard and either the deflector assembly or the vacuum collector adapter are fastened securely in place. MODEL 22610709 - 12 TORO Z-MASTER 2001 PECO 3 PECOPECOPECOPECOPECOASSEMBLY PECOPECOPECOPECOPECOASSEMBLY 4 STEP 1: TO FASTEN CHANNEL CLAMP (A) TO MOUNT PLATE (B) USE (4) 3/8"-16 x 1" HEX BOLTS (#K1191) AND (4) 3/8"- 16 FLANGE NUTS (#K1215). USE FIGURE 1-1 TO PLACE BOLTS. FIGURE 1-1 HOLES TO MOUNT CHANNEL CLAMP A B HOLES FOR MOUNTING TO MOWER

If not corrected, the 2nd start time will default to the Off mode. Press the Copy button to compare settings. Also refer to the Alerts function on page 44 for additional information. 7. Turn the Upper Line knob right to select the 2nd Start Type screen. The High ET start time option is Off by defualt. To program, turn the Upper Line knob right to display the following setup screen. 2nd Start/Windo........ A V_J 8. Repeat the editing procedure used to enter the 1st start time and water window

Or, to restore defaults to all stations , turn the Lower Line knob to select All Stations. COPY STATION DEFAULTS TO ALL STA's (Press BUTTON) 4. Press and hold the Copy button. Release the button when Copying Done is displayed. CT- COPYING......DONE! 41 Restoring PROGRAM Default Settings A\ Important: Restoring the default Program settings erases and resets all user-defined settings for all programs as follows: 1st Start Time - 12:00am Water Window - 05:00 Water Window - 16:00 Water Day M

The station will shut off when the runtime counts down (or is adjusted down) to 00.0 minutes. Each station will operate in sequence for the selected runtime. Note: To terminate operation, either reduce the station runtime to 00.0 or turn the Function Selector knob momentarily to the OFF position. 63 The Run Function RUN is the Function dial position for normal controller operations. However, automatic controller operation will occur when the Function Selector knob is in any position other th

This wire is designated as the valve “Common Wire.” Connect the remaining wire from the solenoid to one of the color-coded wires. Important: All wire splices must be insulated with grease caps or similar waterproofing devices. Step 3- At the timer, connect the control wires to the numbered terminals in the desired operating sequence and the valve common wire to the common terminal. Step 4- Using the timer’s manual control feature, test the operation of each valve. Manual Operation (Figure 4) • B

Where local water pressure exceeds 70 psi, a presure regulator should be used. (See Uniform Plumbing Code, Sec. 1007[b].) It is advisable to use a regulator with any automatic valve to assure long life as well as uniform and controllable operation. Valve Specifications: Operating Pressure: 20–150 PSI Flow Range: 0.25–30 GPM Solenoid: 24 V a.c., 60 Hz (nominal) 19 V a.c., 60 Hz (minimum) Inrush: 0.40 amps, 9.6 VA @ 24 V a.c., 60 Hz Holding: 0.20 amps, 4.8 VA @ 24 V a.c., 60 Hz Friction Loss: GPM

Holding: 0.20 amps, 5.75 VA @ 24 V a.c. • Friction Loss: GPM Flow 0.25 5 10 15 20 30 PSI Loss (3/4") 2.0 4.2 4.2 4.8 7.6 – (1") 2.0 2.1 3.1 2.3 3.8 8.1 Installation Procedure 1. From the shut-off valve, route a supply pipe to the valve installation site. For UV protection, use dark gray Schedule 80 PVC on the inlet (pressurized) side of the valve and all PVC pipe installed above ground. Use Class 200 PVC on the underground sprinkler lines. 2. Flush the supply line thoroughly to remove all traces