See Figure 23. 10.The nuts on the flat head cap screws can be reached from underneath using a 1/2-inch socket, universal, and extension. See Figure 24. 11. Replace or sharpen chipper blade. The blade can be sharpened with a file or on a grinding wheel. 12.When sharpening blade, protect hands by using gloves and follow the original angle of grind. 13.Reassemble by performing the previous steps in the opposite order and manner of removal. NOTE: Tighten blade screws to 210 - 250 in-lbs. Make certai

See Figure 5. b. Pull spring loaded pin out on the base and align pin with the first hole (closest to the end of the tube) in the hose adapter. c. Release the pin to lock the hose in place. 3 Setting Up Your Yard Vacuum IMPORTANT Make sure the cables are routed outside the lower handle. Also, do not crimp the cables while lifting up the handles. A B Rope Guide A B Figure 6 6. a. Snap the hose handle first into the upper hose handle bracket and then into the lower hose handle bracket. See Figure

Then, just before you plant, do one last shallow tilling to destroy the latest batch of weed sprouts. From then on, keep all cultivation shallow, so buried weed seeds stay buried too deep to germinate. Your tiller is ideal for this kind of shallow cultivating, and the work goes quickly because you oniy need to dig an inch or so deep. Some other tips: • Set the depth stake with its sloped edge forward (point backward) to minimize tangling on weeds and to speed up cultivating. Don’t set it too d

This number tells us when your machine was made and what features it has. The arrow in the picture to the right points to the location of the serial number. For your convenience and ready reference, please enter the serial number below and fill in the date your tiller was delivered. The Serial Number On My Tiller Is: Date Tiller was Delivered: A CAUTION TO AVOID INJURY: • READ THE OWNER / OPERATOR MANUAL. • KNOW LOCATION AND FUNCTION OF ALL CONTROLS. • KEEP ALL SAFETY DEVICES AND SHIELDS

This number is necessary so that we can correctly identify your machine. The arrow in the figure at the right points to a location on the top of the transmission housing where the serial number decal is located. For your ready reference, please record this number, along with the delivery date of your tiller, in the spaces provided below. Serial Number:_ Date of Delivery:_ TABLE OF CONTENTS Helpful Information ..................................................................................

Retains dog clutch to shaft........... 2 ____ __ DOG CLUTCH — tiller drive shaft..............f: £&$ KEY — 3/16” square x 1 ”, dog clutch to tiller drive shaft ...................... SPRING — dog clutch ................................................ SHIM — dog clutch, 1/16” (.062”) thick.................................... BOLT — hex. hd., 1 /4”-20 x 7/8”, self locking flange.......................... CAP — rear bearing .................................................. GASKET — rear be

About two or three weeks before planting, till the garden two or three times. Then, till once more before planting. This final tilling helps plants get a head start on future weed growth. When preparing the soil, go over the same path twice in the first row. Then overlap one-half the tilling width on each succeeding pass. See Figure 4-6. After going up and down the rows in one direction, make a second pass at a right angle across your earlier rows. See Figure 4-7. Again, overlap each pass to re

Turn the vehicle engine off and apply the vehicle parking brake. • When going UP ramps, stand in the normal operating position and push the tiller ahead of you. Position a person at each wheel to turn the wheels. • When going DOWN ramps, walk backward down the ramps with the tiller following you. Keep alert for and avoid any obstacles which could cause you to fall. Position a person at each wheel to control the speed of the tiller. Never go down ramps tiller-first, because the tiller could ti

to 7:00 p.m. Sat. 9 a.m. to 4 p.m. For Parts Sales: 1-800-648-6776 For Technical Service: 1-800-833-6990 In Canada: Garden Way Incorporated 320 Van Sickle Road, Unit 12 St. Catherines, Ontario L2R 6P7 Mon.-Fri.: 8 a.m. to 5:00 p.m. For Parts Sales or Technical Service: 1-800-225-3585 CAUTION We urge that you use only genuine TROY-BILT® replacement parts, which meet all of the latest requirements. Replacement parts manufactured by others could present safety hazards even though they may fit on

Call Factory before 63 1166-1 Shim-wheel shaft, 1 -1/64" inner diam.. ordering)................................... 1 .062" thick................................. As Req’d 79 9359 Pin-alignment............................... 1 63 1166-2 Shim-as above, .030“ thick ...... As MISCELLANEOUS PARTS Req’d 80 9560 Bolt-hex hd., 1/2-13 x 2" Grade 5. 2 63 1166-3 Shim-as above, .015“ thick As Req’d 81 9928 Washer-disc spring (concave), domed side faces bolt head....... 2 63 1166-4 Shim-as