Assessments - 0, GPA: 0
(
)
)
|
por este dispositivo também tem outras instruções :
Computadores - HP Integrity NonStop H-Series (16.73 mb)
Computadores - HP Integrity NonStop H-Series (957.56 kb)
Computadores - HP Integrity NonStop H-Series (881.66 kb)
Computadores - HP Integrity NonStop H-Series (965.62 kb)
Computadores - HP Integrity NonStop H-Series (676.93 kb)
Computadores - HP Integrity NonStop H-Series (393.72 kb)
Computadores - HP Integrity NonStop H-Series (776.57 kb)
Facilidade de uso
2353-ed2.book Page 6 Friday, February 9, 2001 6:00 PM
Troubleshooting
Diagnosing with the LEDs
Tip
Problem
Solution
The network
Try the following procedures:
connection is not
• For the indicated port, verify that both ends of the cabling, at the switch and the
working
connected device, are connected properly.
properly.
• Verify the connected device and switch are both powered on and operating correctly.
• Verify that you have used the correct cable type for the connection:
– For twisted-pair connections to the fixed 10/100 ports or to the port on a
100/1000-T transceiver, if the port is configured to “Auto” (auto negotiate), either
“straight-through” or “crossover” cables can be used because of the switch’s “HP
Auto-MDIX” feature and the Auto MDI/MDI-X feature of the 100/1000-T port.
If, however, the switch port is configured with a fixed configuration, for example
100 Mbps/full-duplex, the switch port then operates as MDI-X only, and you must
use the correct cable type for the connection. In general, in this case, for
connecting an end node to the switch, use “straight- through” cable; for connecting
MDI-X ports on hubs or other switches, use “crossover” cable.
– For fiber-optic connections, verify that the transmit port on the switch is connected
to the receive port on the connected device, and the switch receive port is
connected to the transmit port on the connected device.
• For 1000Base-T connections, verify that the network cabling complies with the IEEE
802.3ab standard. the cable should be installed according to the ANSI/TIA/EIA-568-
A-5 specifications. Cable testing should comply with the stated limitations for Attenu-
ation, Near-End Crosstalk, Far-End Crosstalk, Equal-Level Far-End Crosstalk, and Re-
turn Loss.
The cable verification process must include all patch cables from any end devices,
including the switch, to any patch panels in the cabling path.
• Verify that the port has not been disabled through a switch configuration change.
You can use the console interface, or, if you have configured an IP address on the
g
switch, use the web browser interface, or HP TopTools for Hubs & Switches network
i
n
management software to determine the state of the port and re-enable the port if
oot
necessary.
esh
• If the other procedures don’t resolve the problem, try using a different port or a
bl
different cable.
r
ou
T
The port may be
Use the switch console to see if the port is part of a dynamic trunk (through the LACP
improperly
feature) or to see if Spanning Tree is enabled on the switch, and to see if the port may
configured, or
have been put into a “blocking” state by those features. The show lacp command displays
the port may be in
the port status for the LACP feature; the show spanning-tree command displays the port
a “blocking”
status for Spanning Tree.
state by the
Also check the Port Status screen using the show interfaces command to see if the port
normal operation
has been configured as “disabled”.
of the Spanning
Other switch features that may affect the port operation include VLANs and IGMP. Use
Tree, LACP, or
the switch console to see how the port is configured for these features.
IGMP features.
For software troubleshooting tips, see chapter 8, “Troubleshooting” in the Management
and Configuration Guide that came with your switch.
Make sure also, that the device at the other end of the connection is indicating a good
link to the switch. If it is not, the problem may be with the cabling between the devices or
the connectors on the cable.
3-6
... Este manual também é adequado para os modelos :
Computadores - HP Integrity NonStop J-Series (4.21 mb)
Computadores - HP NonStop G-Series (4.21 mb)
Computadores - HP NonStop L-Series (4.21 mb)